Recent content by youfo007

hi, thank you very much for the effort you make. for the link is still down. I found the EMAV2 Protocol on the list supported by the HICOM, but to change the protocol we need permission from the service. between A and B we have 40 km away. I also thought about making a direct connection...

dis-richt ----------------------------------------------------------------------------- |LRTE = 240 NAME = IP CISCO SRVC = ALL | ----------------------------------------------------------------------------- |LDAT |DEST| |ROUT|RE | |FWD|...

a second question : <REG-LDAT; REG-LDAT; H500: AMO LDAT STARTED ADD-LDAT:240,ALL,1,,1,100,1,,1,EMPTY, NONE; ADD-LDAT:240,ALL,1,,1,100,1,,1,EMPTY, NONE; is it possible to have two same LDAT?

<dis-tdcsu; DIS-TDCSU; H500: AMO TDCSU STARTED | | PEN=01-03-025-00| ALARMNO = 0 | PROTVAR = CORNV33 | | DEV=S2CONN +-----------------+-----------------------+---------------------+ | | TCHARG = Y | SUPPRESS = 0 | DGTPR = * | |...

it is possible to trace a call on HICOM ?

and zand & kndef

the problem is identified only in this part lodr? I also want to check the config of the COP, I have no specified parameter? ADD-COP:3,,,;

what does means ECHOALL

in the PABX B I performed all tests, with each change I can't make call from B to CISCO the only solution that has been successful in this PABX B is: ADD-LODR:20,,,ECHO,2; ADD-LODR:20,,,ECHOALL; ADD-LODR:20,,,END; with ADD-LDPLN:8-X-X-X-X-X-X, ,240 ,1,;

<dis-lodr; DIS-LODR; H500: AMO LODR STARTED +-------------------------------------------------------+ | ODR POSITION CMD PARAMETER | +--------+----------------------------------------------+ | 100 | 1 ECHO 1 | |...

<reg-lodr; REG-LODR; H500: AMO LODR STARTED ADD-LODR:100,,,ECHO,1; ADD-LODR:100,,,ECHO,2; ADD-LODR:100,,,ECHO,3; ADD-LODR:100,,,END; ADD-LODR:101,,,ECHO,1; ADD-LODR:101,,,ECHO,2; ADD-LODR:101,,,END; ADD-LODR:102,,,ECHO,2; ADD-LODR:102,,,ECHO,3; ADD-LODR:102,,,END; ADD-LODR:103,,,ECHO,2...

we still meet again, thank you very match. i will change this config in PABX B which connects the two? in the LDPLN we have extention number with 7 figure like (725 6253).

ADD-WABE: 8 , , , TIE , N,,,,, , ; ADD-RICHT:LRTENEW,240,ALL," ", 1,99,,, ,,"",,,11; ADD-LDAT:240,ALL,1,,1,100,1,,1,EMPTY, NONE...

A ---> B ---> Cisco in the pabx B we have: ADD-COT: 3,XFER&ANS&KNOR&CEBC&TIE&CBBN&CBFN&FWDN&FNAN&COTN&TSCS&DTNE; ADD-COSSU:,103,TA&TNOTCR&KNOVR&CDRATN&CDRSTN&CDRS&CDRC&FWDNWK& CDRIND ,,,,,,,,,,; ADD-COP:3,,,; | |...

Hi, I can't make a call from pabx hicom to ipbx cisco through another pabx Pabx hicom A to pabx B to ipbx cisco There are Trunk e1 between A & B and trunk e1 between B & ipbx Pabx A call pabx B n both directions A to B and B to A Pabx B call ipbx cisco also in both directions Ipbx Cisco...