Recent content by Rickg47

Small campus network using OM1 62.5/125 MM cable,all distances under 500 meters need to add a location with a distance of approx 800 meters would adding a single mode fiber cable with single mode media 10/100/1000 baseT converters be the best way to go

I believe the release issue is r7.6 I went back to site to query release and issue. Now I can't login TTY 11 SCH MTC BUG 14:09 OVL111 IDLE 0 >logi USERID? XXXXXXX PASS? XXXXXXX OVL428 TTY 11 SCH MTC BUG 14:10 OVL111 IDLE 0 I do mostly network cabling and hardware set up. I do...

error message temu030 errno 0x4 failure opening file temu032 failure opening database files for writing Tanden Berg tape drive for backup

All slots full with analog and digital line cards.Users don't want analog sets anymore.All digital line cards are full.Can you remove an analog card and replace it with a digital line card.

Can the administrator access these tables to add or remove dn's from say an administration group, so the dn can be used elsewhere or is this question a little simplistic? As I said I know a little,but not a whole lot.

Hope for some direction. I don't know a lot about this system. Something about mapping in call pilot, eg Admin dn 854 belongs to Mary. Mary leaves and her dn 854 is given to john in no particular dept (eg a summer student). Attendant goes into call pilot admin and changes the mailbox. John gets...

I has been awhile since I have dealt with AA CCR No voicemail Just want to answer lies,caller choice to dept no one answers go back to attendant. System co-ordinator manual states"It is recommended that CCR not be programmed to answer lines answered by System answer at the attendent phone" I...

Not sure about procedure for opening more mail box's.I have 79 in use & 3 spares. I understand you have to get keycodes to open more MB's. What increments do they come in. I am puzzled by the odd number of MB's of 83

Upgrading a 15 year old toshiba system.3 lines 10 sets. Cics 6x16 would seem to be a good fit. Since Avaya has taken over,is it true that there are no longer new Cics, only refurb are available?

Thanks again. I thought I did startup as square, but I could of had finger trouble.I will check that when I add the new lines.

Button 9 came up call park. I will use f*81. I terminated the trunks after startup (only 2 for now -getting 2 more) then plugged the sets in and that's the way the T7316e came up button 9(call park),button 10 (line 2) button 11(line 1).I was expecting the T7316e would come up button 9 (Line 1)...

line 1 was assigned to B11, line 2 was assigned to B10 at start up I am going to get another set and try it Thanks

Thanks a few things to check. It was a brand new set on a refurn cics with 7.1. Startup was done,lines were added and sets plugged in. That is how T7316e came up as default. All the other sets wete T7208's and came up fine. Maybe try another T7316e and see what happens to that.

I have a T7316e set. Has 3 buttons under dial pad & label says it's a t7316e, but when it's on the system stn 21 line 1 is on 3rd key, line 2 is on 3rd key. System is a cics 7.1. It's seems like a T7316, but I thought that on the T7316 the lines started on 4th key. Not sure what happening

Incoming calls transfers right to greeting 3 ccr tree 2.Not being really up on cp. Where is the determination made whether the line rings in order to be picked up or goes immediately to the ccr. The Greeting Table 2 in records show MORNING GREETING 2 CCR TREE 1 AFTERNOON GREETING 2 CCR TREE 1...