Recent content by richi23

Thanks acewarlock,

Hi Acewarlock, It works fine when i use NCOS 4 on my phone. Can you please tell me how to activate the CFW from outside my office if i forget to hit the set key "Call Forward" (through the PBX if possible)? Thanks a lot guys for your help.

>ld 87 ESN000 MEM AVAIL: (U/P): 1145017 USED U P: 164421 66817 TOT: 1376255 DISK RECS AVAIL: 401 REQ prt CUST 0 FEAT nctl NRNG 0 7 SOHQ NO SCBQ NO NCOS 0 EQA NO FRL 0 RWTA NO NSC NO OHQ NO CBQ YES RETT 0 RETC 0 ROUT A RADT 0 SPRI 0 MPRI 0 PROM 0 NCOS 1 EQA NO FRL 1 RWTA NO...

Sorry, but still didn't work with tgar 0

>ld 90 ESN000 MEM AVAIL: (U/P): 1145017 USED U P: 164421 66817 TOT: 1376255 DISK RECS AVAIL: 401 REQ prt CUST 0 FEAT net TRAN ac1 TYPE npa NPA 514 NPA 514 RLI 1 DENY 976 SDRR DENY CODES = 1 ITEI NONE >ld 86 ESN000 MEM AVAIL: (U/P): 1145017 USED U P: 164421 66817 TOT...

I not familiar with the route concept but here is a printout of my RDB: \ld 21 OVL001 PT1000 REQ: prt TYPE: rdb CUST SCH0274 CUST 0 ROUT ACOD TYPE RDB CUST 00 DMOD ROUT 0 DES OGT TKTP COT NPID_TBL_NUM 0 PRIV NO SAT NO RCLS EXT DTRK YES BRIP NO DGTP PRI ISDN YES MODE PRA IFC...

acewarlock, How do i know the ACOD? Thanks

The access codes are authentication codes created on ld88 It works with NCOS 4 but the NCOS 4 is setup to dial directly without asking for an aut code. I need to setup the CFW to cell for many users but i need to keep the aut code when they are using their company phone. Thanks,

FTTU didn't help >ld 81 FEA000 REQ cnt CUST 0 DATE PAGE DES FEAT ncos NCOS FEAT FEAT CUST TOTAL SL1 500 2500 3000 2000 3900 ISET DCS NCOS 00 0 CNT 73 0 0 0 0 73 0 0 0 NCOS 00...

DES 3311 TN 003 0 00 02 TYPE 2616 CDEN 8D CUST 0 AOM 0 FDN 7000 TGAR 1 LDN NO NCOS 9 SGRP 0 RNPG 0 SCI 0 SSU 0000 LNRS 16 XLST CLS UNR FBD WTA LPR MTD FNA HTA TDD HFA MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1 POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA CFTD SFA MRD...

Sorry guys i was sick for 3 days and couldn't answer the posts. Yes John the phone can dial the cell number and also LD but with a code. I've also changed CLS to FBD and UNR But still the same issue. Calls from outside to my number go to security instead of the cell number. Thanks

The majority of our phones are on NCOS 0 because setup to be used with a code to dial out. only some are on NCOS 4 and modems are on NCOS 6 Is the only way to make the call forward work to change the NCOS?

I changed my NCOS to 9 but still the same problem

How do i list all the NCOS on the phone system?

Hi all, I have a meridian 11C and i'm trying to forward my DN 3311 to my cell phone. When i call from another DN it says "Release and try again" and from an outside line it goes directly to the reception. I changed CLS to CFXA, CFHA and SFA and OPT on RDR_DATA and FTR_DATA to CFF and Net Data...