Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by liquidshokk

  1. liquidshokk

    Xima Stats Discrepancy

    Anyone know why the total calls in this incoming call report wouldn't equal answered + abandoned? Cheers
  2. liquidshokk

    Avaya IP Office 11.1 Feature Pack 2 Service Pack 3

    Is anyone else seeing DTMF issues in 11.1? We upgrade to 11.1 a couple of months back as advised by Avaya to fix a completely different issue and straight away DTMF wasn't recognised by any external auto attendants. Logged an SR and was advised to switch to Inband DTMF which "fixed" it for 80%...
  3. liquidshokk

    Handset DND Status in IX

    Do you use XMPP group in IX (Workplace?) That's One-X right?
  4. liquidshokk

    Handset DND Status in IX

    It seems that if you put a handset into DND it doesn't show to other users in IX, should it please? I have tried DND buttons as well as Send All Calls. IPO SE 11.1 Thanks
  5. liquidshokk

    IX Headset pickup issue

    Seeing a strange issue with call pickup in IX when using Jabra headset. Users are dialling *53*350# in IX to pickup ringing call but this only works when not using headset. Using headset you just get a long pause and the call doesn't connect. Any ideas?
  6. liquidshokk

    ATA as NAT device

    Apologies, this is a cisco 112 ATA connecting back to MiVoice Office 250 on 6.2, over internet as a NAT device.
  7. liquidshokk

    ATA as NAT device

    Hi Have an analog warehouse bell connected at a remote site via a cisco ATA, which rings when called however the handset making the call continues to display “Enter Destination” as the bell rings and the bell doesn’t stop ringing when putting the receiver down. The ATA is setup as a SIP phone...
  8. liquidshokk

    V10 Manager on XP

    I do and did but missed that one! Just looked for confirmation online too, but it must have been quite a while back as you say... 9.1 works, which made me think 10 would be ok. doh. Thanks!
  9. liquidshokk

    V10 Manager on XP

    Hi Anyone else having problems installing 10.1 manager on XP? I've tried installing the lite and full version but get message saying the file cannot be found?! I've tried running from C: and from the temp folder but get same result. I've tried removing 9.1 first (which installed ok originally)...
  10. liquidshokk

    IPO dropping off network

    Just to update, the IP handsets and link to remote office were down when I visited site and as soon as I move the LAN cable from one switch to another both the handsets and the link came straight up without having to reboot the system so looks like it was the netgear switch port that was faulty...
  11. liquidshokk

    DEE - Overflow to huntgroup

    Does anyone know how you would go about overflowing a users calls from desk, to dect, to huntgroup on a MiVoice 250? Can get the desk twinning with the dect but can't get the call to then overflow. Using a phantom set to forward to the huntgroup as the "home IP" destination, as cannot set a...
  12. liquidshokk

    IPO dropping off network

    I've left pings running to the address so we'll see next time it goes down. Their IT partner assures me that the IPO address is out of the DHCP range........
  13. liquidshokk

    IPO dropping off network

    Have an issue with an IP500 V2 unit on 8.1 randomly dropping off the local LAN every few days. When it is down we can still get to the system via the ISDN lines and all appears to be well, however the IP phones onsite lose sight of the IPO and the SCN goes down. before I start laying into the...
  14. liquidshokk

    10.1

    Anyone know if you need to do anything in PLDS before upgrading from 10.0 to 10.1 or if you just put the upgrade straight through on the system? The docs talk about PLDS and One-Source but don't make it clear. Thanks
  15. liquidshokk

    Server Edition unable to ping out

    I had changed the WAN routing type to ROUTING instead of NAT as part of trying to resolve the issue, and when changing back to NAT I was then able to ping out, so can only assume the draytek was playing up following a recent firmware upgrade! Thanks

Part and Inventory Search

Back
Top