Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by leatherneckdiver

  1. leatherneckdiver

    T-1(Not PRI) connection to a Cisco Call Manager

    I am connecting directly from a Meridian Option 81C Rls 4.5 to a Cisco Call Manager. This is how I have the route and trunks configured now. REQ: prt TYPE: rdb CUST 0 ROUT 51 TYPE RDB CUST 00 ROUT 51 DES GAINES TKTP TIE NPID_TBL_NUM 0 ESN NO CNVT NO SAT NO RCLS EXT VTRK NO NODE DTRK YES...
  2. leatherneckdiver

    Voice treatment for New Route & PRIs

    I have 3 new PRIs which are going into a new route. I have the route and one of the PRIs configured but calls are getting intercepted to the attendant. The route is aquired in Symposium but I'm not sure where else it needs to be set up to give voice treatment. Meridian 1 Rls 4.5 CallPilot 703t...
  3. leatherneckdiver

    Symposium Web Client coresident

    How can you tell if the Symposium server was install as standalone or coresident for Web Client on SCCS 5.0?
  4. leatherneckdiver

    Can't enable cards

    I was in the process of doing your list of options and figured, what the hell, and changed the controller card out while I had the shelf down. The card slot is working now. Never thought a controller card would be the culprit for a single card slot. Thanks for your help.
  5. leatherneckdiver

    Out DN only two DN's tied to single TN

    If you want to remove the DN on key 08 then type nul for key 08. item key 8 nul
  6. leatherneckdiver

    Can't enable cards

    Tried reseating the controller card and still cannot enable any card that is in slot 11.
  7. leatherneckdiver

    Can't enable cards

    There aren't any bent pins on the backplane and cards work in other slots.
  8. leatherneckdiver

    Can't enable cards

    XMI001 & XMI002
  9. leatherneckdiver

    Can't enable cards

    Yes. I can IDC the card.
  10. leatherneckdiver

    Can't enable cards

    Yes. I have an analog phone programmed on that card. I stat the card and it shows idle. I disable and enable the card and get an NPR326 response.
  11. leatherneckdiver

    Can't enable cards

    I have card slot 56-1-11 that I can't enable the card that is in that slot. If I plug/unplug the card in the I get the XMI messages, but cannot enable the card. Thoughts?
  12. leatherneckdiver

    CallPilot message timestamp

    Yes. You have to install a patch for Rls 5 which install a newer version of CallPilot Manager. Once you install that, run the wizard and check the time zone setting. It will be set to a time zone an hour ahead of yours.
  13. leatherneckdiver

    meridian training

    Bad news is no simulator, just lots of OJT.
  14. leatherneckdiver

    Internal call forward off site

    TYPE NET_DATA CUST 00 OPT RTD AC1 INTL NPA SPN NXX LOC AC2 FNP YES ISDN YES VPNI 0 PNI 0 PINX_DN MBG 0 BSGC 65535 PFX1 PFX2 HLOC LSC RCNT 5 PSTN NO TNDM 15 PCMC 15 SATD 1 OCLI NO DITI NO TRNX NO EXTT NO FTOP FRES VNR NO NIT 8 NAS_ATCL NO NAS_ACTV NO FOPT 14 CNTC...

Part and Inventory Search

Back
Top