Recent content by fffrrr

the whole config: Building configuration... Current configuration : 6571 bytes ! ! interface FastEthernet0/0 description *** INTERFACE A INTERNET ** ip address 200.1.2.4 255.255.255.240 ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description...

I think you need this part of the config: ip nat inside source route-map NONAT interface FastEthernet0/0 overload ip nat inside source static tcp 10.10.10.2 80 200.1.2.3 80 extendable ip nat inside source static tcp 10.10.10.1 80 200.1.2.4 80 extendable ! ip access-list standard REDISTRIBUTION...

you need the complete sh runn?

I dont think so, in fact, actually I can access to other web service via WAN through other public IP using the next line: # ip nat inside source static tcp 10.10.10.1 80 200.1.2.4 80 extendable what do you thing?

yes, I have firewall implemented on the network, but in this moment is shut down, just to make this test.

This is the scenario: LAN Server (using IIS service) [/WebFileAsp] <------------> ( Router ) <---------> INTERNET private IP 10.10.10.2 public IP 200.1.2.3 I want to enter through port 80 using the public ip (200.1.2.3) to...

That's right Mitch, wrinting error in both.

OBTAINED SOLUTION: #### ENABLING THE OPTIONS ON THE DESKTOP SCOPE FOR IP PHONES IGNORE THIS POOL G450-001(super-DHCP 10/option 172)# value ascii "L2Q=1,L2QVLAN=200" G450-001(super-DHCP 10/option 172)# exit G450-001(super-DHCP 10)# option 242 G450-001(super-DHCP 10/option 242)# value ascii...

OBTAINED SOLUTION: #### ENABLING THE OPTIONS ON THE DESKTOP SCOPE FOR IP PHONES IGNORE THIS POOL G450-001(super-DHCP 10/option 172)# value ascii "L2Q=1,L2QVLAN=200" G450-001(super-DHCP 10/option 172)# exit G450-001(super-DHCP 10)# option 242 G450-001(super-DHCP 10/option 242)# value ascii...

Sorry if I'm being persistent, but I dont find the solution with this particular problem. I have read about it, I have followed the recommended practices but I still havent got results. This is the link of the problem. http://www.tek-tips.com/viewthread.cfm?qid=1577735

I tested on a 5602 avaya phone. The same, the phone get still parameters of Desktop. After some attempts the next text is displayed: "Contact DHCP/TFTP administrator, L2Q params in option 43/176 or XXX.scr script file have looping conditions" only in 5602 phone appears that text. In the 4602...

I had done already in every single test. But the phone get still Desktop parameters.

Wow Mitch, Im surprised, you are everywhere. ok, Im using a Extreme summit X250e 24t, and with the next conf : #configure "DataUsers" add ports 16 untagged #configure "VoiceUsers" add ports 16 tagged in the VLAN conf on the switch, I configure the VLANID 200 for voice and VLAN 100 for data...

I took a 4602 to test the configuration. I followed your recommendations guys, but the phone get still parameters of "Desktop" scope. In the beginning of the displayed, appears the next: (1) DHCP: counting VLAN ID=0 *the VLAN ID parameter is the only change compares to the initial...

Ok, I understand that, but in this case, I mean, dynamic configuration for ip phones, I need to configure the file server parameter? if the answer is yes, how can I do that?