Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by b106

  1. b106

    ICD groups and voice mail

    Thanks Ired for replying Setting a mailbox in that column had no effect. Obt thank you, auto forward works fine, The auto transfer can be as low as 1 minute Thanks again you have been a great help with all your posts
  2. b106

    ICD groups and voice mail

    Hello All Thanks in advance I have an NS700 with version 9 on it All calls are answered by CS1 Option 2 goes to ICD 602 if not answered goes to ICD 601 Option 3 goes to ICD 603 if not answered goes to ICD 601 Option 4 goes to ICD 604 if not answered goes to ICD 601 ICD 601 is fna to 500 If...
  3. b106

    NS700 sip Trunk

    Hello Attached is a wireshark capture I have 2 channels on the trunk Capture is of a call made from line 1 of the NS700 to my own number giving 503 service unavailable message. I can call out from the NS700 to any other number If I call in to the ns700 from my mobile there is no sip activity...
  4. b106

    NS700 sip Trunk

    Hello Mike I have tried both DIL and DDI still no incoming Hello OBT You mention some settings in the sip trunk card for incoming calls Can you clarify those settings please Thanking You
  5. b106

    NS700 sip Trunk

    Thanks for the replies Apologies for the delay in replying I am just getting over Covid. I can make calls from the ns700 and I have audio both ways I have the lan cable to the NS700 going through a switch with port mirroring on it and I can see the sip messages to and from the NS700 If I try...
  6. b106

    NS700 sip Trunk

    Thanks Fodrod for clarifying that I have made progress in that I can make outgoing calls but no incoming- call does'nt ring at all on the pbx The fact that outgoing calls are ok would suggest the sip side is ok The sip trunk provider uses 10000 to 20000 for voice whereas the DSP card uses 16000...
  7. b106

    NS700 sip Trunk

    Could someone please clarify something for me I am trying to set up a sip trunk on NS700 From reading the posts on here I am wondering should I have 2 IP addresses. I believe my trunk is sip peer trunk Details I was given have 1 IP address for sip server ,no authentation .permit is the static...
  8. b106

    PT programming on TDA 200

    Thanks for that OBT Always very helpful
  9. b106

    PT programming on TDA 200

    Hi Is there any way to see the slot and port that an extension is connected to using PT programming on a TDA 200 Any info on how to assign an extension to a slot/port using PT programming I have gone through all the programming numbers and can't see what I need Thanks in advance
  10. b106

    Hello I have a cordless phone as a

    Hello OBT Thanks for that I am up the road a bit from Kilkenny in Carrickmacross
  11. b106

    Hello I have a cordless phone as a

    Just a follow up Will the EXT-CID card supply caller id info to all slt on the system Does it matter if an slt is on an SLC card or on the DHLC slot Thanks in advance
  12. b106

    Hello I have a cordless phone as a

    Thanks for the reply OBT Very helpful as usual Are you based in Kilkenny by any chance
  13. b106

    Hello I have a cordless phone as a

    Hello I have a cordless phone as an extension (slt)of a TDA 30 This phone will show caller id if used directly across the pstn Will an ext-cid card allow caller id through to the cordless phone when it is an extension? Thanks in advance
  14. b106

    NS700 and licence keys

    Thanks for that
  15. b106

    NS700 and licence keys

    Hello All Just a quick question If you initialise an NS700 with licence key info on it will that licence key be lost Thanks in advance

Part and Inventory Search

Back
Top