Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AZdeserttech

  1. AZdeserttech

    411 and 611 short code question

    qtelcom, If they dial 8911, it will go out on an available POTS line and call e911. If they dial 911 or 9911 (as the customer is instructed to dial), it goes through the ARS 50:Main, System short codes are 9N/dial/N/50:Main and 8N/dial/N/0(line group ID)and emergency dial out on an available...
  2. AZdeserttech

    411 and 611 short code question

    Thanks for the help all, Getting the line provider to fix the routing is an effort in futility (back during the installation, I was not receiving the cpc disconnect signal from the lines. When consulting the plant supervisor, he told me is was 50ms to disconnect, set). Here is what I did...
  3. AZdeserttech

    411 and 611 short code question

    Joe2938, The previous post were tests with my butt set on each line. And yes, they are "copper relics" from the telco, not digital POTS from the cable company. IPGuru, I will test that this morning. Currently it is set as you have posted, except it is set to Main:50, not feature dial. Thank you...
  4. AZdeserttech

    411 and 611 short code question

    Thank you joe2938; The copper lines go off hook immediately, and take anywhere from 2 to 4 seconds per line to connect a call, depending on call routing (rural AZ, local and LD calls). Test system here in shop yields similar results. Greatness is the echo of a life well lived and a job well done.
  5. AZdeserttech

    411 and 611 short code question

    I know this is a newbie question, but I have a customer who dislikes dialing # after 9 and the number ( analog POTS lines, 10 second delay if not dialing # at the end). I have the 7 and the 1 plus 10x short code set up in the ARS, and xN and 10xN removed, but I am brain farting at adding 411 and...
  6. AZdeserttech

    Partner Messaging Module and ACS308: Voice mail/AA issue

    I thought something was odd with the card installation in the carriage. Messaging is in slot 2 and a 308 card is after it on slot 3. Haven't dealt with the Messaging module before. Chalk it up to a little ignorance. I will re-install the cards on Friday and go back through the programming...
  7. AZdeserttech

    Partner Messaging Module and ACS308: Voice mail/AA issue

    Hello all, I have a Partner ACS and Messaging module. The customer got it for free from a defunct business. They have three AA and three lines. Each one is a different business. When the AA kicks in for line 1, It says "mailbox full" after the dial 0 timeout. AA for the other lines works fine...
  8. AZdeserttech

    IP Office 400

    Were are the installation contractor. We have no say on the equipment. And yes, it is an outmoded system. Thanks for the heads up. I currently have 9.0.6.0 Manager installed. I think I have release 8.1 on a cd at the office, but I need to check. The jobsite is an hour and a half away in rural...
  9. AZdeserttech

    IP Office 400

    Hi all, I know this is going to sound like a n00b question (and it is), but do you know what release of Manager is compatible with a 400? The company I am working for cut our teeth on the 500v2. We have an upcoming install where the contractor is leasing the customer the equipment. Thanks in...
  10. AZdeserttech

    CCR Transfer Tree setup issue

    Will do. Thx. I did remove 1 as the park code initially, but will program it as you have suggested. Greatness is the echo of a life well lived and a job well done.
  11. AZdeserttech

    CCR Transfer Tree setup issue

    I was reading another thread where the tech had to set the lines to supervised. I will set that and get back on whether or not it fixes it. Greatness is the echo of a life well lived and a job well done.
  12. AZdeserttech

    CCR Transfer Tree setup issue

    Good day all, I have installed a Call Pilot 100 to a customer's CICS and set up their AA and CCR tree. One of the trees is an outside transfer to an after hours message/paging service. This is my first time setting up this type CCR tree, and I think I am missing something. Programming is: -In...
  13. AZdeserttech

    Nortel CICS with Call Pilot 100: Only first four lines of the system are being answered by the AA

    Sorry for the late reply, I had been busy going from service call to service call. Still no excuse. Thanks to allworxguy [2thumbsup]. What he had posted was correct and worked like a charm [pipe]. Still kicking myself for not seeing it right off the bat. Greatness is the echo of a life well...
  14. AZdeserttech

    Nortel CICS with Call Pilot 100: Only first four lines of the system are being answered by the AA

    Sorry for the long delay to reply back. Work has been hectic (Thankful for being busy). The Call Pilot was set wrong. Adding the corresponding line/port numbers fixed it. Thanks for the heads up. Greatness is the echo of a life well lived and a job well done.
  15. AZdeserttech

    Nortel CICS with Call Pilot 100: Only first four lines of the system are being answered by the AA

    I meant to say it is higher than release 6.0 in the earlier post. Line assignments on the CICs show 1-4 as 001-004 and 5-8 as 031-034. Greatness is the echo of a life well lived and a job well done.

Part and Inventory Search

Back
Top