Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by AH64Armament

  1. AH64Armament

    MiVoice business Console

    can the workstation reach the phone system? What happens when you attempt to run the wizard?
  2. AH64Armament

    Mitel Business- How to change the order of a ring group

    I'm assuming you're using a "Cascade" order on the ring group. The only way I know how to is to remove everyone and put them into the order you want. I've only built a Cascade Ring group one time and it was quickly changed to "ring all" with overflows to other ring groups that add other...
  3. AH64Armament

    Mitel Sx200 digital

    I have seen line cards kill a bay. Pull all the cards from slots 1-8 and power it back on. If the Bay Control comes up, then it's likely one of the line cards. Put them in, one at a time. and see which one kills the bay. Where are you located?
  4. AH64Armament

    Mitel Sx200 digital

    Did you make sure the power cord was plugged into the back of the bay power supply properly? There's a little access cover, undo it, and plug it in.
  5. AH64Armament

    MPA on CX-II, or MXe-III

    That's what I thought too. Figured I'd check while trying to fix this old shiva plug probe. I did get it to work. It just took a while for it to appear as checked in and ready. I repeated the process twice before I noticed it happen.
  6. AH64Armament

    MPA on CX-II, or MXe-III

    Has anyone here managed to install the MPA probe blade on a 3300 ICP that is running on a CX-II or MXe-III? I have a site that has an older Marwatch probe, and of course Martello support has told me to contact Mitel Support. Mitel Support basically said they don't know anything about any such...
  7. AH64Armament

    Mitel Chapter 11

    I agree... hopefully they come back stronger than before. As for the merger with intertel, they became difficult to work with Sales and Marketing after the merger. The impression they gave dealers is that they bought out Intertel as it was a failing company that Mitel wanted some parts of...
  8. AH64Armament

    Mitel Chapter 11

    Mitel filed Chapter 11 bankruptcy the other day. I've been working on Mitel systems since 1997 and have noticed a significant change in structure (detriment) in the past few years. The most recent change is migration from AMC to the Licenses and Services hasn't been a good experience. I have...
  9. AH64Armament

    Mitel 3300 MXE III

    Drive is bad or corrupt. If the system has two drives, pull one of them and power it up. If that didn't resolve it, put it back in and pull the other and try again. If the system only has one drive, you'll need to rebuild the system. You'll need the following: 1 - the most recent backup. 2...
  10. AH64Armament

    SX-200 MX password

    ooh.. handy!
  11. AH64Armament

    SX-200 MX password

    I wonder if you'd be able to figure it out from the output from this. I wonder if the 12-digit code is an ASCII code. https://pbxbook.com/other/mitel/sx200pass.html The procedure for defaulting the password on an SX200 is as follows: From maintenance, login with the username of: password and...
  12. AH64Armament

    SX-200 MX password

    The OP said it is an MX controller. The Serial port is on the front. The L/ML/EL, etc could be accessed by any cabinets Maintenance port on the back.
  13. AH64Armament

    SX-200 MX password

    I'm following this. I have worked on Mitel systems since 1997 and I have worked on all flavors of the SX200 from Analog to ICP and have had several systems that we maintain that we only have access to Maint1. The EL processor cards has a Serial connector near the MOSS chip (without looking, I...
  14. AH64Armament

    Database alarm override commands dont work in 10.1

    Is the backup failing? Back up through the server-manager.
  15. AH64Armament

    SDS alarms/SDS Form Comparison

    I missed the part that it appeared to be an ARS entry that was failing. One of the first sites we set up SDS for, they had shared as many forms as possible - including ARS digits dialed (and others). This wreaked havoc on SDS errors for similar issues. As pointed out, the Route List entry...

Part and Inventory Search

Back
Top