Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
SIP trunks to IP Office
- Thread starter telcodog
- Start date
From the UCx programming, the SIP Trunk can be peer with no registration. I have a SIP Trunk peer-to-peer with a BCM 50 Rls. 6.0 with no issues. I can't speak for the IP Office.
The UCx would look similar to this:
host=192.168.1.2 <IP Address of your BCM or IP Office>
type=peer
trunk=yes
qualify=yes
insecure=port,invite
deny=0.0.0.0/0.0.0.0
permit=192.168.1.2/255.255.255.255
I hope this helps and have a blessed day!
Stocking Distributor for E-Metrotel
The UCx would look similar to this:
host=192.168.1.2 <IP Address of your BCM or IP Office>
type=peer
trunk=yes
qualify=yes
insecure=port,invite
deny=0.0.0.0/0.0.0.0
permit=192.168.1.2/255.255.255.255
I hope this helps and have a blessed day!
Stocking Distributor for E-Metrotel
- Thread starter
- #4
Comcast SIP Trunks have not been fully tested and currently are not on the supported list of SIP Trunk Providers. I think E-Metrotel may looking into testing but haven't heard of anything yet.
I don't know the settings for the IP Office since I don't work on those, however, the UCx will do peer-to-peer with or without registration. If the IP Office requires registration, then the UCx can accommodate that as well. It will all come down to making sure both ends are communicating to each other in the same protocol. I know that isn't what you were asking for, but maybe check with an IP Office person to see how that switch is set up for SIP Trunking.
Stocking Distributor for E-Metrotel
I don't know the settings for the IP Office since I don't work on those, however, the UCx will do peer-to-peer with or without registration. If the IP Office requires registration, then the UCx can accommodate that as well. It will all come down to making sure both ends are communicating to each other in the same protocol. I know that isn't what you were asking for, but maybe check with an IP Office person to see how that switch is set up for SIP Trunking.
Stocking Distributor for E-Metrotel
Hey Telcodog, are you still trying to figure out how to do make SIP trunks work between the IP Office and UCx? I have it completed and it works quite well. I can try and post my settings here later on.
Joseph Sus Jr. Nortel Enthusiast
Joseph Sus Jr. Nortel Enthusiast
- Thread starter
- #7
Yessir!!! If you have it working please post the config details for both systems. My customer is going to replace the IP Office with a UCx but not for about 3 months while his other BCMs are converted but in the meantime, he would like to call between sites over his mpls network.
Thanks for getting it working.
Thanks for getting it working.
Ok, First on your IP Office, log in the Avaya IP Of
fice Manager.
1-Right Click on Line
2-Select New
3-Choose SIP Line
4- Under the SIP Line Tab
a.) choose Line number that you want to name this line, mine is named 18
5-Fill in the Tabs on the right SIP entry with the following screen shots:
Then on the UCx use these two screen shots:
Let me know if it works!
Joseph Sus Jr. Nortel Enthusiast
1-Right Click on Line
2-Select New
3-Choose SIP Line
4- Under the SIP Line Tab
a.) choose Line number that you want to name this line, mine is named 18
5-Fill in the Tabs on the right SIP entry with the following screen shots:
Then on the UCx use these two screen shots:
Let me know if it works!
Joseph Sus Jr. Nortel Enthusiast
Let me try some better images for the IP Office tabs, hang tight.
Joseph Sus Jr. Nortel Enthusiast
Joseph Sus Jr. Nortel Enthusiast
- Thread starter
- #12
No problem, I should have explained that the IP address of the UCx is default 192.168.1.200
Joseph Sus Jr. Nortel Enthusiast
Joseph Sus Jr. Nortel Enthusiast
- Status
