num025
Technical User
- Sep 8, 2008
- 195
Guys, we're having some problems with our new DIOD E1-CAS R2 MFC installation. Right now we were successful with inbound calls and 7-digit outbound calls, however anything beyond a 7-digit call would end up with dead air (no rings). I've checked this with our carrier and they told us that we were only sending a 7-digit ANI, which is why we could do those local calls and not the long NDD and IDD ones.
By the way, below are the pages of our DS1, Trunk and Multifrequency configs:
I'm not even sure if there's anything more that needs to be changed at the multifrequency table, but any suggestions would be highly appreciated. Thanks!
By the way, below are the pages of our DS1, Trunk and Multifrequency configs:
Code:
display ds1 01b11
DS1 CIRCUIT PACK
Location: 01B11 Name: Bayantel E1R201
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: CAS
Interconnect: CO Country Protocol: 7
Interface Companding: alaw CRC? n
Idle Code: 11111111
Slip Detection? n Near-end CSU Type: other
Echo Cancellation? n
display trunk-group 1 Page 1 of 22
TRUNK GROUP
Group Number: 1 Group Type: diod CDR Reports: y
Group Name: E1R2 DIOD Test COR: 1 TN: 1 TAC: 400
Direction: two-way Outgoing Display? n
Dial Access? y Busy Threshold: 255
Queue Length: 0 Country: 7
Comm Type: voice Auth Code? n Digit Absorption List:
Prefix-1? y Trunk Flash? n Toll Restricted? y
Trunk Type: immed-start
display trunk-group 1 Page 2 of 22
Group Type: diod Trunk Type: immed-start
TRUNK PARAMETERS
Outgoing Dial Type: mf Incoming Dial Type: mf
Trunk Termination: rc
Digit Treatment: absorption Digits: 3
Expected Digits: 7 Sig Bit Inversion: none
Analog Loss Group: 6 Digital Loss Group: 11
Trunk Gain: high Drop Treatment: silence
Disconnect Supervision - In? y Out? y
Answer Supervision Timeout: 10 Receive Answer Supervision? y
Administer Timers? y
display trunk-group 1 Page 3 of 22
TRUNK FEATURES
ACA Assignment? n Measured: none
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? y
Charge Conversion: 1
Decimal Point: none
Currency Symbol:
Charge Type: units Receive Analog Incoming Call ID: disabled
Time(sec) to Drop Call on No Answer: 0 MF Tariff Free? n
Outgoing ANI: Ds1 Echo Cancellation? n
display multifrequency-signaling Page 1 of 4
MULTIFREQUENCY-SIGNALING-RELATED PARAMETERS
Incoming Call Type: group-ii-mfc ANI Prefix: 02
Outgoing Call Type: group-ii-mfc Default ANI: 02
Maintenance Call Type: none NEXT ANI DIGIT
Incoming: send-ani
Outgoing: send-ani
Maximum Resend Requests:
Received Signal Gain (dB): 0
Transmitted Signal Gain (dB): -3
Request Incoming ANI (non-AAR/ARS)? y
Outgoing Forward Signal Present Timer (sec): 15
Outgoing Forward Signal Absent Timer (sec): 30
MF Signaling Intercept Treatment - Incoming? y Outgoing: tone
Collect All Digits Before Seizure? y
Private Group II Permissions and Public Interworking? n
Use COR for All Group II Responses? n
Group II Called Party Category: user-type
Use COR for Calling Party Category? n
display multifrequency-signaling Page 2 of 4
MULTIFREQUENCY-SIGNALING-RELATED PARAMETERS
Request Call Category at Start of Call? n
Restart ANI from Caller Category? y
Number of Incoming ANI Digits: 0
Number of Outgoing ANI Digits: 0
Truncate Station Number in ANI: no
Address Digits Include End-of-digits Signal? n
Call Category for Vector ii-digits? n
Request CPN at Start of Call? n
Do Not Send Group B Signals to CO? n
ANI Source for Forwarded & Covered Calls: caller
INCOMING OUTGOING
ANI Available:
ANI Not Available:
display multifrequency-signaling Page 3 of 4
MULTIFREQUENCY-SIGNALING-RELATED PARAMETERS
INCOMING FORWARD SIGNAL TYPES INCOMING BACKWARD SIGNAL TYPES
(Tones from CO) (Tones to CO)
Group-I Group-II Group-A Group-B
11: ignored 1: normal 1 : next-digit 2 : intercept
12: ani-not-avail 2: normal 3 : end-of-dial 3 : busy
13: ignored 3: maint-call 4 : congestion 4 : congestion
14: ignored 4: normal 5 : send-ani 6 : free
15: ignored 5: attendant : :
6: data-call : :
7: toll-auto : :
8: normal : :
9: data-verify : :
10: toll-operator : :
11: normal : :
12: normal : :
13: normal : :
14: normal : :
15: normal : :
display multifrequency-signaling Page 4 of 4
MULTIFREQUENCY-SIGNALING-RELATED PARAMETERS
OUTGOING FORWARD SIGNAL TYPES OUTGOING BACKWARD SIGNAL TYPES
(Tones to CO) (Tones from CO)
Group-I Group-II Group-A Group-B
15: end-of-digits 1 : normal 1: next-digit 1: free
: 2 : attendant 2: congestion 2: free
: 6 : data-call 3: end-of-dial 3: busy
: : 4: congestion 4: congestion
: : 5: send-ani 5: free
: 6: setup-sppath 6: free
: 7: last-2-digits 7: free
: 8: last-3-digits 8: intercept
: 9: last-digit 9: free
: 10: restart 10: free
: 11: congestion 11: congestion
: 12: congestion 12: congestion
: 13: congestion 13: congestion
: 14: congestion 14: congestion
: 15: congestion 15: congestionI'm not even sure if there's anything more that needs to be changed at the multifrequency table, but any suggestions would be highly appreciated. Thanks!