Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

1720 + WIC-1ENET 1

Status
Not open for further replies.
SQL2KDBA69

SQL2KDBA69

Programmer
Feb 4, 2004
227
US
I cant get my ethernet card to get reconized by my router here is what it says when it boots up:


Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-BNR2SY-M), Version 12.2(6c), RELEASE SOFTWARE (fc
1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Sat 02-Feb-02 05:52 by pwade
Image text-base: 0x800080E0, data-base: 0x80B3EFF8

cisco 1720 (MPC860) processor (revision 0x601) with 24576K/8192K bytes of memory
.
Processor board ID VMS062407ET (3983256338), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

transport input none
^
% Invalid input detected at '^' marker.



Press RETURN to get started!


00:00:05: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID of 0xFF
00:00:06: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
00:00:07: %SYS-5-CONFIG_I: Configured from memory by console
00:00:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed
state to up
00:00:09: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-BNR2SY-M), Version 12.2(6c), RELEASE SOFTWARE (fc
1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Sat 02-Feb-02 05:52 by pwade
00:00:09: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold star
t
00:00:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed
state to down


Notice this line :

00:00:05: %PQUICC-1-UNKNOWN_WIC: PQUICC(0), WIC card has an unknown ID of 0xFF


Please help.
 
Sort by date Sort by votes
I have a 1720 with a WIC-1ADSL in slot 0 and a WIC-1ENET in slot 1 and I don't have a problem. I am however running 12.3(17) IOS.

I have seen the problem you describe on other WIC/VIC modules that were unfortunately counterfeit. Did you get the card from eBay, via China by any chance?

Try the command 'show diag' and compare it to what mine looks like for the relevent WIC slot:

WIC/VIC Slot 1:
Ethernet 10bT
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 3.0
Part Number : 73-5797-03
Board Revision : A0
Deviation Number : 0-0
Fab Version : 02
PCB Serial Number : VMSXXXXXXXX
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Top Assy. Part Number : 800-09311-03
Connector Type : 01
Chassis MAC Address : 0004.dd0c.XXXX
MAC Address block size : 1
Product (FRU) Number : WIC-1ENET=


HTH

Andy
 
Upvote 0 Downvote
yeah got it off ebay here is what it says :

WIC Slot 0:
Unknown
Hardware revision 64.0 Board revision G0
Serial number 0960561920 Part number 130-18710-165
Test history 0x03 RMA number 66-65-48
Connector type PCI
EEPROM format version 4
EEPROM contents (hex):
0x20: 04 FF 40 00 39 41 03 00 82 49 16 A5 03 42 41 30
0x30: 80 00 00 00 00 02 02 C1 8B 56 4D 53 30 36 32 36
 
Upvote 0 Downvote
I think it might just be an IOS issue, the counterfeits usually have the 1st byte of the EEPROM as 0xFF, whereas yours is 0x04. You are running 12.2(6c) this isn't listed as compatible on the software advisor...... The problem is you only have 32MB DRAM and 8MB FLASH; what feature set do you need?

12.3(17) IP will work but all other feature sets of 12.3(17) need more memory. The only 12.2 IOS that is listed as supporting the WIC-1ENET card is 12.2ZH (32MB & 16MB)and 12.2YA (32MB & 8MB), but again both of these are IP only images.

I would suggest you download 12.3(17) IP and see if it recognises the card, if it does but you need a different feature set then you will need more memory.

HTH

Andy

 
Upvote 0 Downvote
Great where im i going to get 12.2YA .

i dont care about the feature set. just an image that can fit on my router and reconize the card.
 
Upvote 0 Downvote
ok this worked : c1700-sy-mz.122-11.T.bin

any one know what feature set it has and can it do SSH?
 
Upvote 0 Downvote
All the IP only images don't have any crypto features (you need this for SSH). The image you list is the IP PLUS image but the particular version - 12.2(11)T is not even listed on CCO as deferred so it probably full of bugs....

The nearest I can find on CCO is 12.2(13)T16 IP PLUS but this needs 48MB DRAM & 8MB FLASH....


Andy
 
Upvote 0 Downvote
how many dram slot does the 1720 have. Like can i put two chips in there.
 
Upvote 0 Downvote
ok i registered on the cisco site. how do i get access to the image files.
 
Upvote 0 Downvote
Ahh, its not quite that simple. You need to either be a partner with a support contract or you need to have a maintenance contract (SmartNet) for the equipment you have. When you purchased the router you have the option of taking software maintenance (on a yearly basis I think?). You then register the contract against your CCO ID and you can then download software for your specific device.
Your Cisco supplier should also be able to give the software as long as you aren't changing feature sets. They may charge a nominal fee if you don't have a support contract with them though...

There are however other ways of obtaining IOS, but they aren't exactly 'legal'.

Andy
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Sycho123321
  • Locked
  • Question
T1 wic configuration
Replies
0
Views
130
Sycho123321
Sycho123321
MarkMallow
  • Locked
  • Question
Cisco 1720 fails on 1 of 2 protocols?
Replies
6
Views
104
MarkMallow
MarkMallow
Jerako
  • Locked
  • Question
Removing switch out of LAN segment into router with WIC
Replies
2
Views
89
stubnski
stubnski
jdaley1980
  • Locked
  • Question
Can see my WIC-2T card
Replies
1
Views
139
whykap
whykap
8Bits
  • Locked
  • Question
2620 Install new WIC 2
Replies
6
Views
151
8Bits
8Bits

Part and Inventory Search

Sponsor

Back
Top