ZAND TONES & IPDA

[GZgidnick]

Hi,

Simple question I guess but something I just can't figure out and can't find it in the documentation.

I have given ZAND TONES.
<disp-zand:tones;
DISP-ZAND:TONES;
H500: AMO ZAND STARTED
CP-TONETABLE
============
CP | SIU
---------+----
INTDTN | 1
EXTDTN | 2
SPEC | 1
RNGBK | 4
FRNGBK | 1
BUSY | 5
OVRTN | 6
CAMP | 7
DATA | 9
HOLDLINE | 16
NOTREACH | 17
NOPO | 18
NOTALWD | 19
IMPOSSFM | 20
MOH | 22
NACK | 5
PACK | 1
VOICEMAL | 0
MWI | 1
CONG | 5
NU | 8
OFFHKTRQ | 0
RTCHKNTF | 2
LCRET | 26
RECDIALT | 1
CAMPRBK | 4
BRKMSGWT | 0
CONFTN | 24
TEST | 0
EXTDTN2 | 13
BONHK | 5
NODIAL | 5
HOLD | 0
ALERT | 7
CBKALERT | 4
OVR | 6
OVRWARN | 0
REORDER | 5
LOCANN | 0
KNCONF | 7
DND | 4
PACKWD | 1
ZIPTONE | 2
ANNICPT | 16
RTOTON1 | 2
RTOTON2 | 2
FCAMP | 7
DISCTONE | 8
CMALTONE | 2
HOLDEXT | 16
HOLDINT | 22
HOLDHUNT | 4
HOLDCCS | 4
HOLDH1 | 16
HOLDH2 | 22
HUNTGRUP | 4
POSTDIAL | 1
CCMABSEN | 5
HOWLTONE | 0
ROUTTONE | 0
REQDIALT | 0
SECDIALT | 2
CONFDISC | 0

AMO-ZAND -111 SYSTEM DATA
DISPLAY COMPLETED;
<

Than I remote Shelf TONES.
<DISP-UCSU:AP,1,17;
DISP-UCSU:AP,1,17;
H500: AMO UCSU STARTED
+---------+-------------------+---------+--------------+----------+--------+
|ADDRESS |EXPECTED CONFIGUR. |STATE |LTUC MODULE |LTU-TYPE |FRMTYPE |
| +-------------------+---------+--------------+----------+--------+
| |CONNTYPE LOCATIONID LOCATION SRCGRP |
| |PHONE: FAX: |
| |LSRTADDR APRTADDR BCHL BCHLCNT PLCHECK SIGNAL. |
| |IP MODE DHCP V4 DHCP V6 AP REDUNDANCY TO APXY STATUS |
| |CONVLAW CONTROL UNIT TCLASS ALARMNO |
| |CNTRYCD SIGMODE |
| +----------------------------------------------------------------+
| |SIGNAL. ENCRYPTION ACTIVE [ ] PAYLOAD ENCRYPTION ACTIVE [ ] |
| |SECURE STATE : SEE DESCRIPTION AT BOTTOM |
+---------+-------------------+---------+--------------+----------+--------+
|AP 1.17|ADDED |READY |Q2329-X |AP370016 |SOCOAP |
| +-------------------+---------+--------------+----------+--------+
|SOCOTYPE |APNW 017 HOBART SG 17 1 |
|SOCO1000 |PHONE: FAX: |
| |192.168.066.001 192.168.067.001 250 250 NO LAN |
| | IPV4 NO NO AP REDUNDANCY TO AP |
| | NO HOST-CC 0 0 |
| |4 HSRTCP |
+---------+-------------------+---------+--------------+----------+--------+
| |SIUANN : 2 SIUC : 04 DTR : 04 |
| +----------------------------------------------------------------+
| |CP / SIU : (* = SAME VALUE AS IN ZAND) |
| | INTDTN : 1* EXTDTN : 2* SPEC : 3 RNGBK : 4*|
| | FRNGBK : 1* BUSY : 5* CAMP : 7* DATA : 9*|
| | NACK : 5* PACK : 1* TEST : 0* CONG : 5*|
| | NU : 8* EXTDTN2 : 13* BONHK : 5* NODIAL : 5*|
| | HOLD : 0* ALERT : 7* CBKALERT : 4* OVR : 6*|
| | OVRWARN : 0* RTOTON1 : 2* RECORDER : 5* OVRTN : 6*|
| | CONFTN : 24* MOH : 22* KNCONF : 7* DND : 4*|
| | PACKWD : 1* RTOTON2 : 2* DISCTONE : 8* CMALTONE : 2*|
| | HOLDLINE : 16* NOTREACH : 17* NOPO : 18* NOTALWD : 19*|
| | IMPOSSFM : 20* VOICEMAL : 0* MWI : 21 LOCANN : 0*|
| | ANNICPT : 16* HOLDEXT : 16* HOLDINT : 22* HOLDHUNT : 4*|
| | HOLDCCS : 4* HOLDH1 : 16* HOLDH2 : 22* FCAMP : 7*|
| | HUNTGRUP : 4* POSTDIAL : 1* LCRET : 26* CCMABSEN : 5*|
| | HOWLTONE : 0* ZIPTONE : 2* ROUTTONE : 0* REQDIALT : 0*|
| | SECDIALT : 2* RECDIALT : 1* CAMPRBK : 4* BRKMSGWT : 0*|
| | OFFHKTRQ : 0* RTCHKNTF : 2* CONFDISC : 0* |
+---------+-------------------+---------+--------------+----------+--------+
| |TEXTSEL / LANGID : NO DIFFERENCE TO ZAND |
+---------+-------------------+---------+--------------+----------+--------+
H22: SPE NOT ACTIVATED, NO SPE RESULT STATE INFORMATION AVAILABLE.

AMO-UCSU -111 UNIT CONFIGURATION OF SWITCHING UNIT
DISPLAY COMPLETED;


The * means tones in UCSU and ZAND are same.
There are some different however and would like to make them same.

How do I change the UCSU TONES?

 

[Moriendi]

For example, to change 'please hold the line' to ring back (tone 4 on zand tones).

CHANGE-UCSU:UNIT=AP,LTG=1,LTU=17,CP=HOLDLINE,SIU=4;

 

[GZgidnick]

thank you Moriendi