When on a call your second ringing button rings too loud.

[Frav82]

Good Morning,

On all of our phones (OptiPoint 410 HFA) if you are on your Prime line and a call comes in on another button the ringer for that call is really loud. Even when you adjust the actual phone ringer on your phone to it's lowest level the line appearance buttons will still ring really loud if you're on your Prime line. I'm a relative newbie to Siemens and I can't seem to find any adjustment to control this. Shouldn't this be the other way where the second ringing button rings quietly because you're already on a call? (OpenScape 4000 V7 R2)

Thank you, have a nice weekend!

Rob

 

[hipath4k]

Hi,

You can change this ringer by opti setting in

Cha-zand

 

[Frav82]

I'm a former NEC technician and I'm still kind of new to Siemens so I'm not too sure which entry needs changed and what to change it too. Here is what I have when looking at our zand:

DIS-ZAND:ALLDATA;
H500: AMO ZAND STARTED
GENERAL SYSTEM DATA:
====================
TRANSFER = EXTEND , ALERTN = NO ,
AUTHUP = TA ,
RNGBKTN = YES , TRANSINH = NO ,
NIGHT = TA ,
ITRFWD = YES , HOLDTN = MUSIC , ANATESIG = TONE ,
DSSLT = 10, CODTN = YES , CONFSUB = YES ,
DATEDIS = MMDD, CNTRYCD = K , RCLLT = NO ,
MELODY = 1, TRCD = , CPBLOWL = 80 ,
CPBUPPL = 100, CUTHRU1A = NO , PREDIA = NO ,
SIUANN = D, CO = YES , COEXN = 0 ,
CBKNO = 5 , SEVDIG = NO , PNNO = 200,
DISPMODE = MODE1, PNODECD = ***200, ROUTOPTP = NO ,
ROUTOPTD = YES , CALLOFF = YES , PARARING = NO ,
DSSDEST = YES , ONEPARTY = NO , MSGDELAY = NO ,
EXCOCO = YES , TRDGTPR = NO , COANN = YES ,
HOTDIAL = NO , TRANSTOG = NO , NOCFW = NO ,
HOLDHUNT = NO , POSTDDLY = NO , EXBUSYOV = NO ,
OVRMST = NO , OVRHUNT = NO , CONITPRO = NO ,
RECHUNT = YES , CALLACMP = NO ;

 

[hipath4k]

cha-zand
type=? ( Enter)

Pls give me result

 

[Frav82]

POSS. VALUES : CIT COMPUTER INTEGRATED TELEPHONY
CONFC CONF BRANCH (COMPACT HW)
ALLDATA ALL SYSTEM DATA
ALLDATA2 ADDITIONAL ALL SYSTEM DATA
ALLDATA3 ADDITIONAL TO ALL DATA2
DIUSL TABLE DEP_LOCK_TBL FOR SOFT LOCK
DIST DIVERSION SEQUENCE TABLE
CCD MODIFY CALL CHARGE DISPLAY FOR STATION AND ATND
LCR SETTING OF LCR COS
LOADWARE LOADWARE VARIANT FOR 1 MODULE
LEDTYPE ASSIGNMENT OF LED CADENCES TO 5 LED SITUATIONS
MLPP MULTI-LEVEL PRECEDENCE AND PREEMPTION SERVICE
OPTISET SETTINGS FOR OPTISET DEVICES
OPTTBL MODIFY OPTIONSTABLE IN DB
RESERVE SETTING OF RESERVE ELEMENTS IN FUNCT_SWITCH_SET
CCM MULTIPLE CODE CALLING
RNGTYPE RING TYPE (DIRECT STATION SELECTION, ETC)
SIUXPER SET LEVEL VARIANTS FOR SIUX-DTMF/MFC
TN TONES BRANCH
TONES TONE TABLE, CP <-> SIU ASSIGNMENT

 

[hipath4k]

dis-zand
type= OPTISET SETTINGS FOR OPTISET DEVICES

here you can control volume

 

[Frav82]

[pre]POSS. VALUES : ATND SETTINGS FOR ATTENDANT CONSOLE
ACD SETTINGS FOR ACD-G
VMI SETTINGS FOR VOICE MAIL INTERFACE
DOMAIN SETTINGS FOR DOMAIN IDENTIFICATION OF CUG
KEYSYS SETTINGS FOR KEY SYSTEM
ACC SETTINGS FOR ACCOUNT CODE[/pre]

 

[hipath4k]

Hi,

Is it possible to provide remote access via any desk

 

[sbcsu]

The ringing volume and types are controlled via the AMO KCSU
If you REG-KCSURIM; and REG-KCSU:,SEC;
You will then see the individual ringing volumes and tones for each line presentation

 

[Frav82]

Unfortunately not at this time I have to leave for a meeting at 8:30 at our main hospital. We have a lot of changes happening at the direction of corporate right now. Hopefully this meeting will only last a couple hours. Thank you hipath4k hopefully I can catch you later today.

 

[hipath4k]

CHA-ZAND:OPTISET,24HOUR,EUROPE,ENGLISH&GERMAN&FRENCH&SPANISH&ITALIAN,19,3,3
,4,3,3,NORMAL,50,7,YES,2,NO,4,2,3,NO,NO,NO,NO,NO,,YES,NO