Valcom Paging system

[RossV]

I have a valcom 2006a that needs to be hooked up and I'm having a hard time getting the port to transmit any audible sound. The access code gives you side tone from the set you dial it from but when you put a butt set on the port you get nothing. I'm punched on white blue pair of the TN 4 1 2 Here is how it's built:

ROUT 77


TYPE RDB
CUST 00
ROUT 77
DES NEWBLDPAG
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 5477
CPP NO
TARG
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MR NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0


PAGE 002

FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR N0

Trunk:

DES PAGNWBLD
TN 004 1 02 00 VIRTUAL
TYPE COT
CDEN 8D
CUST 0
XTRK EXUT
FWTM NO
TIMP 600
BIMP 3COM
AUTO_BIMP NO
TRK ANLG
NCOS 0
RTMB 77 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO


Any suggestions? (there are no other members in the route)

 

[PERRYPJ]

Change RDB and TRUNK to WATS

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[Wane47]

these are the dip switch options for the 2006A. I'm a little confused about you cannot hear side tone (do you mean dial tone or blow back battery?) from a butt set, but you can hear it from a pbx set. any rate this is the dip switch option for dial tone on a valcom 2006A.

Switch 3 pos 1 off=dial tone on=no dialtone.

It can also be set to use grd start or loop start. the following is from the manual. You can get the manual on the internet.

Loop/Ground Start Access
If the V-2006A/V-2006AHF is being used with
Loop/Ground Start Access, set SW6 to Up (ON). SW2
selects loop or ground start access from the telephone
system. SW1 selects loop or ground start access for
the override feature.
NOTE: When using a ground start trunk port, a
ground strap must be used to connect GND of the
V-2006A or V-2006AHF to an appropriate telephone
system ground (see Figure 1).