Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
upgrade 1.3 to 3.1
- Thread starter polaroid
- Start date
Stage 12b. Two-Stage Upgrades
Due to the need to adjust internal memory allocation, for certain upgrades, some control units have needed to perform a two stage upgrade process. These processes normally only need to be performed once.
Control Unit
Upgrade
Stages Required
IP403
To levels between 2.0 and 2.1(27)
The IP403 must first be upgraded to level 1.99. Once upgrade to 1.99, the unit can be further upgraded to levels from 2.0 upwards.
To 2.1(28) or higher
In this scenario, the IP403 must first be upgraded to level 2.99. Once upgraded to 2.99, the unit can be further upgraded to level from 2.1(28) or higher. This is a one-time process that does not need to be repeated.
IP406 V1 and V2
To 3.1 or higher.
In this scenario the control unit must first be upgraded to level 3.0(999). Once upgraded to 3.0(999), the unit can be further upgraded to 3.1.
Procedure
Start IP Office Manager.
Select File | Advanced | Upgrade.
The upgrade wizard will list the modules found, their current software level and software levels for those modules that Manager has available.
Right-click on the upgrade wizard and click Select Directory.
If upgrading an IP403 to between 2.0 and 2.1(27) inclusive, select the IP403V1_99 folder within the Manager program directory.
If upgrading an IP403 to level 2.1(28) or higher, select IP403V2_99 the folder within the Manager program directory.
If upgrading an IP406 V1/V2 to level 3.1, select IP406_V1 or IP406_V2 as appropriate.
The upgrade wizard should now list just the control unit as having upgrade software available.
If upgrading from pre-2.1 software, untick Validate and see the note below.
The validated upgrade option is only supported for modules which already have 2.1 or higher software installed. If doing an unvalidated upgrade, you must be using a PC with a fixed IP address and on the same LAN segment as the IP Office control unit.
Tick the checkbox next to the IP403 module name and then click Upgrade.
Enter the system password when requested.
Following the upgrade, stop and restart the upgrade wizard. The upgrade wizard will again show the software levels available in the Manager program folder and allow all the modules in the system to be upgraded.
this can be found at:
very useful tool if you plan on doing a lot of IPO's
Diz
Due to the need to adjust internal memory allocation, for certain upgrades, some control units have needed to perform a two stage upgrade process. These processes normally only need to be performed once.
Control Unit
Upgrade
Stages Required
IP403
To levels between 2.0 and 2.1(27)
The IP403 must first be upgraded to level 1.99. Once upgrade to 1.99, the unit can be further upgraded to levels from 2.0 upwards.
To 2.1(28) or higher
In this scenario, the IP403 must first be upgraded to level 2.99. Once upgraded to 2.99, the unit can be further upgraded to level from 2.1(28) or higher. This is a one-time process that does not need to be repeated.
IP406 V1 and V2
To 3.1 or higher.
In this scenario the control unit must first be upgraded to level 3.0(999). Once upgraded to 3.0(999), the unit can be further upgraded to 3.1.
Procedure
Start IP Office Manager.
Select File | Advanced | Upgrade.
The upgrade wizard will list the modules found, their current software level and software levels for those modules that Manager has available.
Right-click on the upgrade wizard and click Select Directory.
If upgrading an IP403 to between 2.0 and 2.1(27) inclusive, select the IP403V1_99 folder within the Manager program directory.
If upgrading an IP403 to level 2.1(28) or higher, select IP403V2_99 the folder within the Manager program directory.
If upgrading an IP406 V1/V2 to level 3.1, select IP406_V1 or IP406_V2 as appropriate.
The upgrade wizard should now list just the control unit as having upgrade software available.
If upgrading from pre-2.1 software, untick Validate and see the note below.
The validated upgrade option is only supported for modules which already have 2.1 or higher software installed. If doing an unvalidated upgrade, you must be using a PC with a fixed IP address and on the same LAN segment as the IP Office control unit.
Tick the checkbox next to the IP403 module name and then click Upgrade.
Enter the system password when requested.
Following the upgrade, stop and restart the upgrade wizard. The upgrade wizard will again show the software levels available in the Manager program folder and allow all the modules in the system to be upgraded.
this can be found at:
very useful tool if you plan on doing a lot of IPO's
Diz
- Status
Similar threads
