thread798-1621188
Hello everyone,
I have the same problem as described in the above closed thread798-1621188.
For a fresh new install of my lab equipment I had to wipe the MGC card completly using mgcIPclear, diskformat and reboot it. However for some reason I am no longer able to go in oam or ldb using CTRL+LDB. All I see is " ^L^D^B ". Same with CTRL+OAM. I see only "^O^A^M"
I am using direct serial Port 0 from octopus cable.
I have tried with a different keyboard, same result. I rebooted the MGC several time, there's nothing I can do.
Here is the output message I get right now at the serial Port 0:
regWithMainCabinet: RPC: Port mapper failure - RPC: Timed out
Failed to Register with Primary Call Server[10.44.143.2]
STARTUP: unable to send registration request to Primary Call Server.
In the closed thread mentioned above the solution was the following:
-----------------------------------------------------------------------------------------------------------------------
CS 1000E 5.5: Unable to access Media Gateway Card (MGC) shells on new cards
Problem Description:
On brand new cards out of the box, following an upgrade to the current loadware on the Call Server (CS) the Operations, Administration and Maintenance (OAM) and Local Debug Mode (LDB) shells are not accessible. After connecting to the cards getting the login prompt and password prompt, then the banner scrolls and that is it. Unable to get to the OAM prompt or LDB prompt. This issue is only seen on brand new cards.
Symptoms:
* No prompts
* Cannot manage card
* No output to Teletypewriter (TTY)
Problem Resolution
Manual workaround:
1. Telnet into the MGC which you will not be be to access properly.
2. Go to LDB level (Ctrl + L, D, B).
3. Type in "remove /p/cspversion.txt" and hit the RETURN key.
To verify it:
ftp <MGC IP address>
cd /p
Ensure cspversion.txt gets deleted otherwise repeat step 3.
(You cannot see anything echo on this hosted screen)
4. Repeat step 1, you can login into this MGC normally.
There is no need to reboot the MGC.
----------------------------------------------------------------------------
What I dont understand and what my question is, is about Point 1. from the solution above: "Telnet into the MGC which you will not be be to access properly."
--> How can I telnet into the MGC??
The MGC settings are erased. I dont know the default IP settings from the MGC. How can I telnet into MGC then?
Can somebody help?
It would be very much appreciated!
Thanks in advance
Here a picture from my card:
Hello everyone,
I have the same problem as described in the above closed thread798-1621188.
For a fresh new install of my lab equipment I had to wipe the MGC card completly using mgcIPclear, diskformat and reboot it. However for some reason I am no longer able to go in oam or ldb using CTRL+LDB. All I see is " ^L^D^B ". Same with CTRL+OAM. I see only "^O^A^M"
I am using direct serial Port 0 from octopus cable.
I have tried with a different keyboard, same result. I rebooted the MGC several time, there's nothing I can do.
Here is the output message I get right now at the serial Port 0:
regWithMainCabinet: RPC: Port mapper failure - RPC: Timed out
Failed to Register with Primary Call Server[10.44.143.2]
STARTUP: unable to send registration request to Primary Call Server.
In the closed thread mentioned above the solution was the following:
-----------------------------------------------------------------------------------------------------------------------
CS 1000E 5.5: Unable to access Media Gateway Card (MGC) shells on new cards
Problem Description:
On brand new cards out of the box, following an upgrade to the current loadware on the Call Server (CS) the Operations, Administration and Maintenance (OAM) and Local Debug Mode (LDB) shells are not accessible. After connecting to the cards getting the login prompt and password prompt, then the banner scrolls and that is it. Unable to get to the OAM prompt or LDB prompt. This issue is only seen on brand new cards.
Symptoms:
* No prompts
* Cannot manage card
* No output to Teletypewriter (TTY)
Problem Resolution
Manual workaround:
1. Telnet into the MGC which you will not be be to access properly.
2. Go to LDB level (Ctrl + L, D, B).
3. Type in "remove /p/cspversion.txt" and hit the RETURN key.
To verify it:
ftp <MGC IP address>
cd /p
Ensure cspversion.txt gets deleted otherwise repeat step 3.
(You cannot see anything echo on this hosted screen)
4. Repeat step 1, you can login into this MGC normally.
There is no need to reboot the MGC.
----------------------------------------------------------------------------
What I dont understand and what my question is, is about Point 1. from the solution above: "Telnet into the MGC which you will not be be to access properly."
--> How can I telnet into the MGC??
The MGC settings are erased. I dont know the default IP settings from the MGC. How can I telnet into MGC then?
Can somebody help?
It would be very much appreciated!
Thanks in advance
Here a picture from my card:
