Unable to do 4 digit dialing anymore to Mexico

[ttdredd1]

We setup 4 digit dialing to our Mexico site for CA. As of last Thurs we are unable to dial. We get a busy signal.

Here is a printout of what we setup.
We setup route 44 and 13 to dial out and to let them call us.

What could be wrong?

TYPE TLST

TKTP DID
ROUT 44
DES MEXICO
TN 028 01 MBER 1
TN 028 02 MBER 2
TN 028 03 MBER 3
TN 028 04 MBER 4
TN 028 05 MBER 5
TN 028 06 MBER 6
TN 028 07 MBER 7
TN 028 08 MBER 8
TN 028 09 MBER 9
TN 028 10 MBER 10
TN 028 11 MBER 11
TN 028 12 MBER 12
TN 028 13 MBER 13
TN 028 14 MBER 14
TN 028 15 MBER 15
TN 028 16 MBER 16
TN 028 17 MBER 17
TN 028 18 MBER 18
TN 028 19 MBER 19
TN 028 20 MBER 20
TN 028 21 MBER 21
TN 028 22 MBER 22
TN 028 23 MBER 23
TN 028 24 MBER 24

REQ: LTM
CUST 0
ROUT 13
TYPE TLST
TKTP DID
ROUT 13
DES ATT L.D.
TN 002 01 MBER 1
TN 002 02 MBER 2
TN 002 03 MBER 3
TN 002 04 MBER 4
TN 002 05 MBER 5
TN 002 06 MBER 6
TN 002 07 MBER 7
TN 002 08 MBER 8
TN 002 09 MBER 9
TN 002 10 MBER 10
TN 002 11 MBER 11
TN 002 12 MBER 12
TN 002 13 MBER 13
TN 002 14 MBER 14
TN 002 15 MBER 15
TN 002 16 MBER 16
TN 002 17 MBER 17
TN 002 18 MBER 18
TN 002 19 MBER 19
TN 002 20 MBER 20
TN 002 21 MBER 21
TN 002 22 MBER 22
TN 002 23 MBER 23

DES
TN 028 01
TYPE DID
CDEN SD
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 0
RTMB 44 1
A/B BIT SIGNALING
NITE
SIGL EAM
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
AACR NO
DATE 14 JUL 2005

REQ: PRT
TYPE: TN
TYPE TNB
TN 2 1
DATE
PAGE
DES

DES
TN 002 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 13 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD HKD
P10 VNL
TKID
AACR NO
DATE 7 JUL 2005

 

[acewarlock]

What kind of 4 digit dialing?

CDP or ACOD???

More then likely there is a problem with your RLB in LD 86.

DEo a PRT DNB of 1 of the number's and see where it sends you.

 

[ttdredd1]

We are using CDP.

Can't do a print on the DNB because we really don't have one for those line. We use Digital munipulation.

 

[jamie2]

Verify that your RLB's are using the correct DMI. You issues are going to be some where in LD 86 most likely.

 

[acewarlock]

Do a Print of your CDP and post.

 

[ttdredd1]

here is the CDP:

TYPE DSC
DSC 13
DSC 13
FLEN 0
DSP LSC
RLI 16
NPA
NXX

The difficult part about all this is, I don't have access to our Mexico plant. They have been complaining about dead air while on a call or dead air. I think maybe there phone person or vendor made some type of change, but I don't know what it is since they are convinced that everything on their end is ok.

 

[ttdredd1]

I also checked and we are using the correct DMI.

The first choice previously entered for 4-digit dialing just sends the call across the route/span. It hits Mexico's PBX and outpulses the 4 digits. The second choice redirects the call over public transport by inserting the full number, much like dialing direct. The DMI for the second choice should look like, "delete 0; insert international country code - city code - exchange".

Everything looks fine, can't pinpoint the problem.

 

[acewarlock]

Sounds like the other end to me also.

 

[johnpoole]

ld 60 stat 13 ? not usually a software change unless someone was adding dsc's.. if the pri is up and the d is estb, then have someone on site dial the acod plus a working dn on the far end..

john poole
bellsouth business
columbia,sc