Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Trunk to Trunk 1

Status
Not open for further replies.

someguy758

Technical User
Nov 3, 2005
130
US
I have a problem with performing a trunk to trunk transfer from an analog trunk to a ip trunk, the ip trunk goes to a another site. The extensions at the remote have the ability to use our analog trunks to make calls. I get an incoming pstn call, I press transfer the 1st time i get the beeps and dialtone, dial an extension at the remote site person answer but when i try to press the transfer button a second time nothing happens, as if the button has stopped working. I have tried CLS FTTU on the set doing the transfering, tried EXTT yes, FTOP ftly, trnx yes, diti yes, tried analog trunk with and without answer supervision it is currently set to SUPN no.
System is a CS1000E 5.5 remote site also a CS1000 5.5

Any suggestions?

Thanks
 
Have you verified from the Telco that the Lines have Supervision turned on? Also I know that for whatever reason Loop Start Lines and Supervision did not work well with the PBX, I have always used Ground Start and had better luck with Supervision.
 
The lines are loop start with no supervision, putting supervision on was just to try to see what would happen.
 
Yes I understand that, but even if you turn it on in programming does not mean that you really have supervision. The Telco has to have it on on there end also. I have had problems in the past with transfering from analog to PRI lines and supervision did correct that.
 
The lines are programmed as loop start with no supervision and telco has lines as loop start no supervision. Do i need to have the telco put supervision on the line to get this working?
 
telco can't help with that one.. your route is supv no? that would denote supervision is remote.. ie pstn..

can you complete the transfer post answer?

i would toggle supv. another workaround.. what are your inbound pstn programed as? if they are did's change your end to tie.. ndec/fdec eth supv no

john poole
bellsouth business
columbia,sc
 
Cant complete transfer post answer. I have tried supervision on and off for the analog trunk.

Trunk config:
DES
TN 004 1 03 01 VIRTUAL
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 600
TRK ANLG
NCOS 0
RTMB 0 2
ATDN 8116
SIGL LOP
SUPN NO
AST NO
IAPG 0
SEIZ NO
CLS UNR DTN CND ECD WTA LPR APN THFD SPCD
P10 NTC
TKID
AACR NO
DATE 10 DEC 2008

Route config:
TYPE RDB
CUST 00
ROUT 0
DES
TKTP COT
NPID_TBL_NUM 0
PRIV NO
RPA NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO YES
ACMP NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 787898
TARG
CLEN 1
BILN NO
OABS
MFC NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 3
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
ARP 3
SFB 3
CRD 512
TFD 0
LEXT 100
SST 3 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DDO NO
DRNG NO
CDR YES
INC NO
LAST NO


PAGE 002

QREC NO
OAL YES
AIA YES
OAN YES
OPA NO
OPD NO
NDP EXC 0
CDRX NO
CCO NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
MR NO
PANS YES
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
RCAL NO
MCTS NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 0
SGRP 0
CCB NO
CCBA NO
ARDN NO
AACR NO

IP route:
TYPE RDB
CUST 00
ROUT 99
DES
TKTP TIE
M911P NO
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK YES
ZONE 020
PCID H323
CRID NO
NODE 276
DTRK NO
ISDN YES
MODE ISLD
DCH 99
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
FALT NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
MBXR NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 88999
TCPP NO
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
PTUT 0
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896


PAGE 002

SFB 3
NBS 2048
NBL 4096
TFD 0
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
PANS YES
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 88999 99
ATRR NO
TRRL NO
SGRP 0
CCBA NO
ARDN NO
AACR NO

IP Trunk:
DES
TN 156 0 00 00 VIRTUAL
TYPE IPTI
CDEN 8D
CUST 0
XTRK VTRK
ZONE 020
LDOP BOP
TIMP 600
BIMP 600
AUTO_BIMP NO
NMUS NO
TRK ANLG
NCOS 0
RTMB 99 1
CHID 1
TGAR 1
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DIP CND ECD WTA LPR APN THFD XREP SPCD
P10 NTC
TKID
AACR NO
DATE 1 DEC 2008

 
Ok i missed that one, changed NEDC and FEDC on ip trunk to eth and it works now.

Thanks.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top