johnrusl
Technical User
- Oct 23, 2004
- 9
This should be an easy question for somebody. How do you set the time and date on a CTX 100?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations gkittelson on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Toshiba CTX 100 setting time and date
- Thread starter johnrusl
- Start date
- Status
Found this on another site:
(note: for the older DK systems this had to be done from the first/lowest port, usually extension 10 or 200; not sure if that restriction still applies to the CTX)
Toshiba CTX
To set date:
Leave the handset in the cradle.
Press the Intercom key + # 651 (Listen for the confirmation tone).
Enter the date in the YYMMDD format.
Press the # key. (Listen for the confirmation tone)
To set time:
Leave the handset in the cradle.
Press the Intercom key + #652 ( Listen for the confirmation tone).
Enter the time in 24 hour clock format. (HHMMSS)
Press the # key. Listen for the confirmation tone.
Hope this helps
(note: for the older DK systems this had to be done from the first/lowest port, usually extension 10 or 200; not sure if that restriction still applies to the CTX)
Toshiba CTX
To set date:
Leave the handset in the cradle.
Press the Intercom key + # 651 (Listen for the confirmation tone).
Enter the date in the YYMMDD format.
Press the # key. (Listen for the confirmation tone)
To set time:
Leave the handset in the cradle.
Press the Intercom key + #652 ( Listen for the confirmation tone).
Enter the time in 24 hour clock format. (HHMMSS)
Press the # key. Listen for the confirmation tone.
Hope this helps
- Thread starter
- #3
ProviderReborn
Technical User
Do you have emanager/winadmin?
ACA - IP Office Implement
ACA - IP Telephony
ACS - IP Office Implement
CCNA - Working towards.
ACA - IP Office Implement
ACA - IP Telephony
ACS - IP Office Implement
CCNA - Working towards.
Here are the instructions to change the system time on CTX 100:
1. At any display phone, press HOLD
2. Enter *#*#1*2*3
3. At the PWD= prompt, enter 0000, then press HOLD
4. At the PROGRAM= prompt, enter 902, then press HOLD
5. Press line 1 (this is the key above the Intercom key), then enter time in 00:00:00 format. Use Military time.
6. Then press HOLD HOLD ## HOLD.
Here are the instructions to change the date on CTX 100:
1. Press the hold button
2. Dial * # * # 1 * 2 * 3 *
3. Enter password xxxx
4. Press hold button
5. Dial 902
6. Press hold button
7. Press bottom button on vertical line buttons (bottom left if 20 button telephone)
8. Enter date as YYMMDD ie: 04 01 01 (Jan 1st 2004)
9. Press hold button
10. Press hold button again
11. Lift handset and hang up to end program
1. At any display phone, press HOLD
2. Enter *#*#1*2*3
3. At the PWD= prompt, enter 0000, then press HOLD
4. At the PROGRAM= prompt, enter 902, then press HOLD
5. Press line 1 (this is the key above the Intercom key), then enter time in 00:00:00 format. Use Military time.
6. Then press HOLD HOLD ## HOLD.
Here are the instructions to change the date on CTX 100:
1. Press the hold button
2. Dial * # * # 1 * 2 * 3 *
3. Enter password xxxx
4. Press hold button
5. Dial 902
6. Press hold button
7. Press bottom button on vertical line buttons (bottom left if 20 button telephone)
8. Enter date as YYMMDD ie: 04 01 01 (Jan 1st 2004)
9. Press hold button
10. Press hold button again
11. Lift handset and hang up to end program
ProviderReborn
Technical User
VM type?
Do you know what mailbox your main menu is in?
ACA - IP Office Implement
ACA - IP Telephony
ACS - IP Office Implement
CCNA - Working towards.
Do you know what mailbox your main menu is in?
ACA - IP Office Implement
ACA - IP Telephony
ACS - IP Office Implement
CCNA - Working towards.
- Status
Similar threads
- Locked
- Question