Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

TMDI/MSDL issue

Status
Not open for further replies.

oneeyebrow

Technical User
Mar 7, 2011
42
US
Hello,

Recently on an Option 11c I configured to TMDI cards for installation of two new PRIs (slots 0 0 1 and 0 0 2). The ADAN was programmed with a primary and back up channel. There already existed three PRIs (two for DIDs with an primary and back up and separate one - slots 0 0 3, 0 0 4 and 0 0 5). For the new install, I converted slot 0 0 2 from a trunk card to a PRI one.

Today the phone switch power cycled. When it came back up, it appears the TMDI card in slot 0 0 2 converged with MSDL card in 0 0 5 (if that makes any sense). See below:

From cequ:

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 020 24 ESF YES B8S FDL 0 00 000 0 01
021 24 ESF YES B8S FDL 0 00 000 0 02
022 24 ESF NO B8S FDL - 00 000 0 03
023 24 ESF NO B8S FDL - 00 000 0 04
024 24 ESF NO B8S FDL - 00 000 0 05
025 23 ESF NO B8S FDL - 00 000 0 06

Here's stat msdl in ld 96:

MSDL 000 0 3 ENBL
MSDL 000 0 4 ENBL
TMDI 000 0 2 MAN DSBL
MSDL 000 0 6 ENBL

and TMDI:

TMDI 000 0 1 ENBL
TMDI 000 0 2 MAN DSBL

Here's the adan for the two d-channels:

ADAN DCH 6
CTYP MSDL
MG_CARD 000 0 05
PORT 1
DES MCI
USR PRI
DCHL 24
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO


ADAN BKUP DCH 12
PDCH 11
CTYP TMDI
MG_CARD 000 0 02
PORT 1
BCHL 21
RCVP NO
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

Any thoughts? Before the power outage, MSDL 0 0 5 was working. Thanks.
 
Here's the slt. I don't see anything on here regarding TMDI, so maybe I can't use TMDI in this system? This is my first crack at this. Thanks.

REQ slt

System type is - Communication Server 1000E/CP PM
CP PM - Pentium M 1.4 GHz

IPMGs Registered: 3
IPMGs Unregistered: 0
IPMGs Configured/unregistered: 0


ANALOGUE TELEPHONES 88 LEFT 58 USED 30
CLASS TELEPHONES 0 LEFT 0 USED 0
DIGITAL TELEPHONES 400 LEFT 246 USED 154
DECT USERS 0 LEFT 0 USED 0
IP USERS 30 LEFT 17 USED 13
BASIC IP USERS 0 LEFT 0 USED 0
TEMPORARY IP USERS 0 LEFT 0 USED 0
DECT VISITOR USER 0 LEFT 0 USED 0
ACD AGENTS 16 LEFT 16 USED 0
MOBILE EXTENSIONS 0 LEFT 0 USED 0
NORTEL SIP LINES 0 LEFT 0 USED 0
THIRD PARTY SIP LINES 0 LEFT 0 USED 0

PCA 0 LEFT 0 USED 0
ITG ISDN TRUNKS 0 LEFT 0 USED 0
H.323 ACCESS PORTS 0 LEFT 0 USED 0
AST 1 LEFT 1 USED 0
SIP CONVERGED DESKTOPS 0 LEFT 0 USED 0
SIP CTI TR87 0 LEFT 0 USED 0
SIP ACCESS PORTS 36 LEFT 0 USED 36
RAN CON 0 LEFT 0 USED 0
MUS CON 0 LEFT 0 USED 0

TNS 32760 LEFT 31947 USED 813
ACDN 24000 LEFT 23978 USED 22
AML 16 LEFT 16 USED 0
IDLE_SET_DISPLAY BINGHAM McCUTCHEN LLP
LTID 32760 LEFT 32760 USED 0
RAN RTE 512 LEFT 512 USED 0
ATTENDANT CONSOLES 32760 LEFT 32759 USED 1
BRI DSL 10000 LEFT 10000 USED 0
DATA PORTS 32760 LEFT 32760 USED 0
PHANTOM PORTS 32760 LEFT 32759 USED 1
TRADITIONAL TRUNKS 32760 LEFT 32622 USED 138
DCH 255 LEFT 248 USED 7
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top