Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

TMDI card tie to Cisco CM in Red Alarm

Status
Not open for further replies.

CommoGuy101

Technical User
Nov 6, 2009
236
US


Morning everyone,

I have recently added a TMDI card to our option 11.
There are 2 functioning TMDI cards already active(slot 1 being the CC)
I have added this particular TMDI to slot 3.
I was able to get the d-channel and all of the b-channels built.
Enabled the TMDI.
Connected a crossover cable between the option 11 an the Cisco.

When I enll 3 all of the b-channels are in disabled state.
The D-channel goes into OPER mode but then RLS.

PRI* TRK LOOP 3 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : RED
CH 01 - DSBL TIE 3VCE * CH 02 - DSBL TIE 3VCE *
CH 03 - DSBL TIE 3VCE * CH 04 - DSBL TIE 3VCE *
CH 05 - DSBL TIE 3VCE * CH 06 - DSBL TIE 3VCE *
CH 07 - DSBL TIE 3VCE * CH 08 - DSBL TIE 3VCE *
CH 09 - DSBL TIE 3VCE * CH 10 - DSBL TIE 3VCE *
CH 11 - DSBL TIE 3VCE * CH 12 - DSBL TIE 3VCE *
CH 13 - DSBL TIE 3VCE * CH 14 - DSBL TIE 3VCE *
CH 15 - DSBL TIE 3VCE * CH 16 - DSBL TIE 3VCE *
CH 17 - DSBL TIE 3VCE * CH 18 - DSBL TIE 3VCE *
CH 19 - DSBL TIE 3VCE * CH 20 - DSBL TIE 3VCE *
CH 21 - DSBL TIE 3VCE * CH 22 - DSBL TIE 3VCE *
CH 23 - DSBL TIE 3VCE * CH 24 - DCH 3

There is a red alarm light and also an amber light on the card DCH indicator.

It looks like I have the T1E set up properly but the d-channel is not talking to the Cisco.

Not real sure why the T1E has not come up.
Maybe a bad crossover cable or a defective TMDI card.
Any thoughts would be appreciated.

Thank you,
CommoGuy101
 
Are you able to "loop" the RJ45 connections to see if the card enables?. Also, do the same at the Cisco end. You might also need to check that each end uses the same protocol.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
FirebirdScrambler,
As soon as I can get on site I will place a loopback on the RJ45.
Any idea why the DCH LED is amber...(should it be green)(is it amber because it is in red alarm)
The red LED is lit as well ..I know that indicates a red alarm.

Thank you,
CommoGuy101
 
I tend to work on PRI circuits with 30 channels and I'm not that clued up with protocols for other regions, but it would indicate to me that you have incompatibility set in the configuration of your programming.

Here is some information that may assist you below with 3 records found.

#################################

Unable to get D channel to come up between Meridian and Cisco 2600 series routers

Answer

Problems getting D channel and loop to come up between a meridian and a Cisco 2610 router. In this case the Cisco 2610 was expecting to see ACRC set to yes. This was changed to no and the respective change made on the meridian as well. The D channel then came up. (All other parameters as per recommended settings).

Sample configuration as below:
QSIG (ESGF4) to Cisco 2610 series router.

PRI card set to 75 Ohm Coax.
Coax75 ohm to RJ45 125 Ohm converter used to connect to router.

NB, ACRC set to no on the respective loop timer in overlay 73

.REQ: PRT
*TYPE: RDB
*CUST 0
*ROUT 121
*TYPE RDB
*CUST 00
*DMOD
*ROUT 121
*DES QSIG
*TKTP TIE
*NPID_TBL_NUM 0
*ESN NO
*RPA NO
*CNVT NO
*SAT NO
*RCLS EXT
*VTRK NO
*NODE
*DTRK YES
*BRIP NO
*DGTP PRI2
*ISDN YES
* MODE PRA
* IFC EGF4
* SBN NO
* PNI 00001
* NCNA NO
* NCRD NO
* CTYP CDP
* INAC NO
* ISAR NO
* CPFXS YES
* DAPC NO
* INTC NO
*DSEL VOD
*PTYP DTT
*AUTO NO
*DNIS NO
*DCDR NO
*ICOG IAO
*SRCH LIN
*TRMB NO
*STEP
*ACOD 1621
*TCPP NO
*TARG 01
*CLEN 1
*BILN NO
*OABS
*INST
*IDC NO
*DCNO 0 *
*NDNO 0
*DEXT NO
*SIGO STD
*MFC NO
*ICIS YES
*OGIS YES
*TIMR ICF 1920
* OGF 1920
* EOD 13952
* LCT 256
* NRD 10112
* DDL 70
* ODT 4096
* RGV 640
* GTO 896
*
* GTI 896
* SFB 3
* PRPS 800
* NBS 2048
* NBL 4096
*
* IENB 5
* TFD 0
* VSS 0
* VGD 6
*DTD NO
*SCDT NO
*2 DT NO
*DRNG NO
*CDR NO
*NATL YES
*SSL
*CFWR NO
*IDOP NO
*VRAT NO
*MUS NO
*PANS YES
*FRL 0 0
*FRL 1 0
*FRL 2 0
*FRL 3 0
*FRL 4 0
*FRL 5 0
*FRL 6 0
*FRL 7 0
*OHQ NO
*OHQT 00
*CBQ NO
*AUTH NO
*TTBL 0
*ATAN NO
*PLEV 2
*OPR NO
*ALRM NO
*ART 0
*PECL NO
*DCTI 0
*TIDY 1621 121
*SGRP 0
*AACR NO

*PT0000
*REQ: PRT
*TYPE: TNB
*TN 12 1
*DATE
*PAGE
*DES
*
*DES QSIG
*TN 012 01
*TYPE TIE
*CDEN SD
*CUST 0
*TRK PRI2
*PDCA 3
*PCML A
*NCOS 7
*RTMB 121 1
*B-CHANNEL SIGNALING
*TGAR 1
*AST NO
*IAPG 0
*CLS UNR DTN WTA LPR APN THFD XREP BARD
* P10 VNL
*TKID
*AACR NO
*DATE 12 APR 2005

*TYPE ADAN DCH 12
*
*ADAN DCH 12
* CTYP MSDL
* CARD 12
* PORT 1
* DES qsig
* USR PRI
* DCHL 12
* OTBF 32
* PARM RS422 DTE
* DRAT 64KC
* CLOK EXT
* IFC EGF4
* PINX_CUST 0
* ISDN_MCNT 300
* CLID OPT0
* CO_TYPE STD
* SIDE USR
* CNEG 1
* RLS ID 4
* QCHID YES
* RCAP NCT MWI COLP NDI CCBI CCNI PRI DV3I MQC CTI
* PR_TRIGS DIV 2 3
* CNG 2 3
* CTR2 2 3
* PR_RTN NO
* MQC_FEAT NAS NACD NMS
* MBGA NO
* OVLR NO
* OVLS NO
* T310 120
* T200 3
* T203 10
* N200 3
* N201 260
* K 7

*>LD 73
*DDB000
*MEM AVAIL: (U/P): 2483834 USED U P: 557564 71561 TOT: 3112959
*DISK RECS AVAIL: 1024
*REQ PRT
*TYPE PRI2
*LOOP

*PRI2 LOOP 12
*MFF AFF
*ACRC NO
*ALRM REG
*RAIE NO
*G1OS YES
*SLP 5 24 H 30 1 H
*BPV 128 122
*CRC 201 97
*FAP 28 1
*RATS 10
*GP2 20 100 S 12 S 12 S 4 S
*MNG1 15 M
*NCG1 15 M
*OSG1 15 M
*MNG2 15 S
*NCG2 15 S
*OSG2 15 S
*PERS 50
*CLRS 50
*OOSC 5

##########################################

QSIG to Cisco Call manager config, working on a 61c cp3 rls 25.15

ADAN DCH 4
CTYP MSDL
DNUM 13
PORT 0
DES PHILLY
USR PRI
DCHL 4
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID 25
RCAP ND3
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB
CUST 00
DMOD
ROUT 7
DES PHILLY
TKTP TIE
NPID_TBL_NUM 0

ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES

NCRD YES
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 889997
TCPP NO
PII NO
TARG 01
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048

NBL 4096
IENB 5
TFD 0
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 00
CDR YES
INC YES
LAST YES

TTA YES
ABAN YES
CDRB YES
QREC YES
OAL YES
AIA YES
OAN YES
OPD YES
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO

MUS NO
PANS YES
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO


TTBL 0
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 889997 7
SGRP 0
AACR NO

TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 4
PCML MU
NCOS 7
RTMB 7 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD XREP BARD
P10 VNL

###########################################

CISCO HAD TO SET THEIR BOX UP CORRECTLY TO START WITH AND USE A X-OVER CABLE BUT THE FOLLOWING CONFIG SEEMS TO BE WORKING WELL.

TYPE TLST
TKTP TIE
ROUT 120
DES ATT_VPN
TN 004 01 MBER 1 CISCO

REQ: prt
TYPE: rdb
CUST 0
ROUT 120

TYPE RDB
CUST 00
DMOD
ROUT 120
DES ATT_VPN
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY ETSI
SBN NO
PNI 00001
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
SDID NO
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1611
TCPP NO
TARG
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 00
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1611 120
SGRP 0
AACR NO

REQ: ****
OVL000
>*ld 20
REQ: prt
TYPE: tnb
TN 4 1
DATE
PAGE
DES CISCO
TN 004 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 7
RTMB 120 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS UNR DIP WTA LPR APN THFD XREP BARD
P10 VNL
TKID
DATE 3 NOV 2004

ADAN DCH 13
CTYP MSDL
CARD 04
PORT 1
DES cisco
USR PRI
DCHL 4
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC EURO
CNTY ETSI
PINX_CUST 0
ISDN_MCNT 300
CLID OPT1
PROG NCHG
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 25
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 120
OUT_T306 120
T200 3
T203 10
N200 3
N201 260
K 7

TYPE NET_DATA
CUST 00
OPT RTD
AC1 INTL NPA SPN NXX LOC
AC2
FNP YES
ISDN YES
VPNI 0
PNI 1
PINX_DN
MBG 0
BSGC 65535
PFX1
PFX2
HLOC 210
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
TIDM NO
DASC
ROPT NRO
DITI NO
TRNX NO
EXTT NO
FTOP FRES
APAD 0 0
VNR NO
NIT 8
NAS_ATCL YES
NAS_ACTV NO
FOPT 14
CNDN
CNAT
CNIP YES
DMWM NO
MWNS NO
CNTC
NATC
INTC

ld 73

MFF AFF
ACRC NO
ALRM REG
RAIE NO
G1OS YES
SLP 5 24 H 30 5 H
BPV 128 122
CRC 201 97
FAP 28 1
RATS 10
GP2 20 100 S 12 S 12 S 4 S
MNG1 15 M
NCG1 15 M
OSG1 15 M
MNG2 15 S
NCG2 15 S
OSG2 15 S
PERS 50
CLRS 50
OOSC 5








Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Just a quick thought, as long as the T1 is in RED alarm the state of the D channel and associated B channels really don't matter. The D channel requires a good T1 circuit before it will come up, many RED alarm conditions are hardware related, bad cable, card , wrong pin outs etc. The RED alarm is telling you that your card either does not see the T1 circuit or can't read what it is getting. The loopback test suggested should help narrow that down.
 


Thanks drifter,
I will try the loop back
BTW this is a T1E from the option 11 to Cisco gateway.
I will start with the loop back and replace the hardware just in case.

Thank you all for your help,
CommoGuy101
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top