TMANI Caller ID is not working in OS4KV7

[eniyamath]

Hi
i configured as below
caller id is not working
can anyone guide me please
Regards

DIS-COSSU:COS,10;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 10 |>COS FOR TMANI |
| | TA | TA | TA |
| | TSUID | TNOTCR | TNOTCR |
| | TNOTCR | FAX | DSM |
| | CDRC | BASIC | BASIC |
| | MB | MSN | MSN |
| | VCE | | |
| | FWDNWK | | |
| | TTT | | |
| | FWDBAS | | |
| | FWDECA | | |
| | SUTVA | | |
+------+-----------------+---------------+-----------------+
DIS-COT:11;
H500: AMO COT STARTED

COT: 11 INFO: COT FOR TMANI
DEVICE: INDEP SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
CHANGEOVER FROM HOLD TO RING TONE CHRT
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
END-OF-DIAL FOR BLOCK IS SET BLOC
SEND NO NODE NUMBER TO PARTNER LWNC
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR NLCR
USE DEFAULT NODE NUMBER OF LINE DFNN
NO TONE NTON
DIS-COP:12;
H500: AMO COP STARTED

COP: 12 INFO: COP FOR TMANI
DEVICE: INDEP SOURCE: DB
PARAMETER:
DUALTONE MULTIPLEFREQUENCY DTMF
LINE WITH SUPERVISION AND RELEASE ACKNOWLEDGEMENT LSUP
BACKWARD RELEASE AFTER RELEASE RLSA
TIME DEPENDENT EXCHANGE DIALTONE TDED
NOT 1A, I.E OUTGOING DIGITS NOT WITHHELD NO1A
DIRECT INWARD TRUNK, NO AC INTERCEPT DITW
START-DIALING-SIGNAL TIMER 1 (AMO DTIM2: PARAMETER STADIAL1) TIM1
LINE WITH NO START-DIAL-SIGNAL NSDL
MAKE/BREAK RATIO FOR DTMF 1 (PULSE=80MS,PAUSE=80MS) DTM1
DIS-BUEND:10;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 10 TGRP NAME : STC INCOMING MAXIMUM NO. : 15 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 20 DEVICE TYPE : TMANIMSG TRACENO : 0 |
| SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 1 PRIORITY : 1 |
| TDDRFLAG : ON TDDRTHRESHOLD: 0 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 1-103-4 | | | | |
+------------------------------------------------------------------------------+

DIS-TACSU:1-1-103-4;
H500: AMO TACSU STARTED
ANALOG TRUNKS (FORMAT=L)
PEN | 1-1-103-4 | |
--------|--------------------------------|--------------------------------|
DEVTYPE | TC | |
DEV | TMANIMSG | |
COTNO | 11 | |
COPNO | 12 | |
DPLN | 0 | |
ITR | 0 | |
TGRP | 10 | |
COFIDX | 0 | |
CCT | 383 4252 | |
DESTNO | 0 | |
INS | Y | |
COS | 10 | |
LCOSV | 1 | |
LCOSD | 1 | |
INIGHT | | |
NNO | 1-1-10 | |
ALARMNO | 2 | |
CARRIER | 1 | |
ZONE | EMPTY | |
HMUSIC | 0 | |
LIN | 0 | |
CIDDGTS | NONE | |
CBMATTR | NONE | |
SRCGRP | 0 | |
CLASSMRK| EC G711 G729AOPT | |
TCCID | | |
DITIDX | 0 | |
TRTBL | GDTR | |
RULEIDX | 0 | |
ATNTYP | | |
MFCVAR | 0 | |
DGTPR | 6498 | |
SUPPRESS| 0 | |
DGTCNT | 0 | |
TESTNO | 1 | |
CIRCIDX | 4 | |
CRDINT | 1 | |
CCTINFO | 0 | |
DIALTYPE| MOSIG-DTMF | |
DIALVAR | 0-0 | |
COEX | 5 | |
SVCDOM | | |
---------------------------------------------------------------------------

AMO-TACSU-111 CONFIGURATION OF ANALOG TRUNK CIRCUITS IN THE SWU
DISPLAY COMPLETED;
DIS-ZAND:ALLDATA3;
H500: AMO ZAND STARTED
ALL SYSTEM-DATA 3:
==================
NWTOPTIM = 20 SEC , DDSIMPFL = YES ,
CIDBON = YES , RENSFWD = NO ,
NETTEAM = NO , VCOCUG = NO ,
CFUI = NO , NOCFOOO = NO ,
CLIPSTD = ETSIFSK , CFNRDEST = ONLYCFNR,
EXANTRF = NO , IPDAVCCF = NO ,

DIS-FEASU;
H500: AMO FEASU STARTED
ACTIVATED FEATURES

SPDC SPDI HTVCE HTFAX HTDTE OVR FRKN NIGHT
COSXCD COSXKEY DCOSX COSXATND COSXT ICPTDID HOTRCL DND
VARCONF TRACE SNR RKNOVR CBK DSS SPLIT ONHKTRNS
PU SER RNG SYNCANN CDROGTR LCRET POSTBUSY POSTFREE
RELOCATE HTNW PININT TIMEDREM ATTR ECFW CPS INCPRIO
CALOGOPT DIRCPCKP CLIP MOBHFA

DEACTIVATED FEATURES

CRITM LDME COSXDP RSVCO DDTES ISTR NOCHRG WTATND
TRACCO LEDSIGN VMSDP RELCON RERING AUTOV EMOVR EMRLS
DCBB DCBNOA CDRINH CDRIC CDROGNW DISCHINH DISCHNW DISCHTR
VOICO PINNW XFBACALL XFBADIAL CDRE DCPA NCT RCCB
MLPP CDRACC SMARTCRD SILMON

 

[sbcsu]

Hi,
Are you getting the CLI on an ordinary telephone when it is plugged in to the telephone line directly - in other words is the carrier sending the CLIP - thanks

 

[eniyamath]

Dear sbcsu
Yes
first i confirmed the service provider is sending CLI or not
i connected the trunk line directly to euroset 5020 and getting the CLI.
Thanks

 

[sbcsu]

Your configuration seems correct, I have never seen CLI Working from a carrier on an analog line.
I will have to setup the same on a V8 next week and if I can find out any more info I will pass it on.
I don't know if the TMANI can give incoming CLIP ?