TLU76 interworking with CISCO router 6

[GuauGuau]

Hi!
I need to connect an 30B+D ISDN interface of a CISCO router to public ISDN Network. I'm thinking about connecting it to a TLU76, and do transit through MD110 to public ISDN network. I don't know if TLU76 can do that. Can TLU76 emulate public ISDN?

Could anybody help me?

Thanks a lot. Sorry my bad english.

 

[ysgoh88]

Should not be a problem..but you need to tell people what version software of the MD110 is.

 

[GuauGuau]

The PBX is a MD110 BC9 Packet B.
Thanks a lot.

 

[naltalite]

Should not be a problem. MD110 in BC9 is capable of doing ISDN "Network side".

 

[MD6]

Hi,

Only TLU76/1 is a ISDN Trunk (public or private). In MD110 have a :
TLU76/1--> 30B+D ISDN
TLU76/2--> 30B+D DPNSS
TLU76/3--> 30B+D CAS
TLU76/4--> 30B+D For signalling system no. 7 (ONLY BC11 VERSION)

You define if trunk is a public or private in the MD110 program (ROXXX comands).

Good Work

MD6

 

[ges69]

Yes, tlu 76/1 can.
You need to use DSS1 protocoll.

 

[vjimeneztenas]

Tell me what kind of cisco and IOS version you have, maybe I can give you a configuration for the cisco and the PABX

 

[mustafa61]

Hi JimenezT,

We are trying to connect the MD110 BC10 to Cisco 2600. We want to seting up a PRI connection between them. Cisco 2600 is using primary net-5 i think. We couldn't establish a connection. Do you have any parameters for both sides. Or do you have any advice like using the q-sig singnalling. Which one do you prefer qsig or pri.

 

[itcom]

For connection of MD to CIsco please see

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/sw_conf/pbx_int/

It is work.

Best regards,
Alexey Gusev

 

[GASMAS]

We have managed to connect 2 md 110 with Cisco and E1 interface with q sig.
Everything works fine.
Has anyopne managed to have q-sig functionality with 2b+d interface?

 

[dognbone]

I have a site connected to Cisco on a BC9 MD110 using a TLU76/1. Here are the route parameters:-

<ROCAP:ROU=45;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
45 111000010001 3 3100000000 0 30 128 00151515 111110000031 101100

END

<RODAP:ROU=45;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
45 SL60 H'00001310 H'15400000 H'06700000 NO

END


I also manage another BC9 site which connects to a Cisco using a TLU79 (2B+D) and its parameters are:

<RODAP:ROU=70;;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
70 SL60 H'00001144 H'14400000 H'50210000 NO

END

<ROCAP:ROU=70;;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
70 611000001000 3 2100000002 0 30 128 00151515 111110110030 111110

END


Hope this helps.

 

[rrmagno]

I've set up a new route for for TLU76/1 on my MD110 with Cisco router 3600.My MD110 version is LZY2035104/1/CNI85D/R1A.
the parameters that I set up for this route are as follows:

<ROCAP:ROU=81;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
81 012000000000 5 2110000010 0 30 128 00151515 111101100031 001100

<RODAP:ROU=81;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
81 SL60 H'00000210 H'054A0000 H'06300000 NO

<RODDPEST=84;
EXTERNAL DESTINATION ROUTE DATA
DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
50 81 163610000000025000 0 1 0


hope this parameters would help..

 

[vince62s]

maybe this will sound ridiculous but:

when connecting a cisco router to a TLU 76 board:

is this for connecting the router to an ISDN type dial up ISP ?

or is it to connect the MD 110 to an existing network ? subsequently, can we do VoIP with this configuration?

thanks guys

 

[SYAR2003]

Vince !
See my reply in this thread
thread806-703685 setup of md110 qsig networking between e.g two
md's can be utilized with this setup.
TLU76/1 cards connected to cisco ip-router witch have
a G.703 interface .
That for carrying the tie line(qsig) voice data
between the md's over ip-network.

You will need appropriate data set both for the md's
and in the routers.

SYAR

 

[mdfan]

To make it complete :

G.703/G.704 = E1 (PRA/PRI) .


ok vince ?

 

[SYAR2003]

Yeah!

 

[bram123]

MD110 BC11

I want to connect a TL76/3 CAS Trunks via a Router.

Has anyone had any experience?

Could you provide a quick config overview: any funnies I should be aware

RODAP:
ROCAP:
RODDP:

Thanks

 

[sakhan]

These are the parameters for a route setup with CAS\ TLU76/3. Using it only for outgoing. If somebody need for incoming set VARI.


ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
238 001000000000001 5 2100000010 0 30 128 02080812 311110110150 111111

ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
238 TL30 H'00000000 H'00001216 NO


DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE
9000 238 00050000000002500000000 0 5 0

Cheers

 

[bram123]

Thanks Sakhan,

Will give it a try when I'm allowed!

As mentioned previously, I've got TL76/1 working Ok... however the returned speech path i.e the called party returning speech back to the Caller appears to degregate...(gets worse)!.....

 

[73vette]

Does anyone have the Var's, Rodap, Rocap, Rodap for BC9.0 - TLU 76/3 to a Cisco Router?

Thanks