Tie Trunk OpenScape 4000 to Alcatel-Lucent OmniPcx Enterprise V R12.0

[Hamid2018]

Hi dears,

I have a "Openscape 4000 V6 R2.17.1_rc5" and there is a "Alcatel-Lucent OmniPcx Enterprise V R12.0" as tandem switch and want to link with PRI (E1) with following configuration but caller ID which is sent by Openscape 4000 cannot be repeated to CO trunk by tandem switch and when ever one of Openscape users for exmple 6830 dials 011+"a mobile number" the mobile (as cell-phone) user notices the caller ID is 07731312000 while DID 2000 is the call answering operator of tandem.(tandem switch is connected to City telecom over PRI-E1 and is connected to several PABXs with PRI-E1).

ADD-BCSUER,1,2,10,"Q2227-X ",0,0,,,,,,A,0,,;
ADD-COP:5,L3AR&LKNQ&PRMT,,;
ADD-COT:5,PRI&RCL&XFER&KNOR&CEBC&CBBN&CBFN&IEVT&BSHT&BLOC&PROV&ATRS&TSCS&TRSC&CFOS&PINR&AOCC&CTLS&AMFC&NTON;
CHANGE-COT:5,COTADD,,S2COD,"20: S0/2 AMT EDSBRD O. ABWURF";
CHA-COSSU:LCOSV,5,1&11&14;
CHA-COSSU:LCOSV,5,,,,,0;
ADD-COSSU:,5,,,,,,,,;
CHA-COSSU:COS,5,TA&TNOTCR&CDRATN&CDRS&CDRC&CDRIND&CDRINT&RKOABS;
CHA-COSSU:COS,5,CFNR&FWDNWK&TTT&CFB&FWDDIR&FWDECA&FWDEXT&CW;
CHA-COSSU:COS,5,CFKL;
CHA-COSSU:COS,5,,NOCO&NOTIE;
CHA-COSSU:COS,5,,,NOCO&NOTIE;

ADD-BUEND:5,"PRI-ALCATEL ",30,2,*,1,ON,0,0,NEUTRAL;
ADD-TDCSU:NEW,1-01-012-0,5,5,0,0,5,1,1,"ALCATEL PRI ",0,ECMAV2,1,,NONE,,,,GDTR,N,TIE,NONE,N,0,,,,,,,31,MANY,1-1-310,2,1,1,EMPTY,5,10,N,,,,,,16,8,1,10,,EC&G711&G729A,,5,CIR,Y,TRADITIO,0,S2CONN,1&&30,Y,1,2,0,0,0,0,0;

ADD-RICHT:LRTENEW,5,ALL,"ALCATEL ",5,1-1-310,,NO,FIX,DIGITS,"SPGC-REF8-ICT ",PP150,NO,,,,NO,NO,"PRI-2-ALCATEL",0,NEUTRAL,NO,NO,NO,NO,NO,NO,NO,NO;

ADD-LODR:5,,,,ECHO,1;
ADD-LODR:5,,,,ECHO,2;
ADD-LODR:5,,,,END;
ADD-LDAT:5,ALL,1,,5,5,1,,1,EMPTY,WCHREG,,4,,,,,,,,,,,,;
ADD-WABE:011,,,TIE,N,,,,,,,,;
ADD-LDPLN:LCRPATT,0,"011"-"X",0,5,,,11,,,,N;


and the following is configuration of Tandem Switch:
============ About PABX============
Model :Alcatel-Lucent OmniPcx Enterprise
Software Version: R12.0
============ About ============
============ Setting Hardware ============
Shelf 3 Slot 7 (GD3)
Access Board Type: MG-PRA-E1
synchronization Priority : 255 --> Master
Network Mode : Yes
CRC4: Yes
============ Setting Hardware ============
============ Setting Trunk For Incoming & Outgoing Digit ==============
Trunk 8
Q931 signal variant : ABC-F
Private Trunk Group : YES
Trunk Group Details :
Logical Channel : 1-30
Charge Calling And ADN Creation : YES
============ Setting Trunk For Incoming & Outgoing Digit ==============
best regards
Hamid

 

[Hamid2018]

I should note that then I use Cornet with the following command the connection is OK but just using 15 channels of connection except 30 channels:

ADD-TDCSU:NEW,1-1-012-0,5,5,0,0,5,1,1,"ALCATEL PRI ",0,PSS1V2,1,,NONE,,,,GDTR,N,TIE,NONE,N,0,,,,,,,31,MANY,1-1-310,2,1,1,EMPTY,5,10,N,,,,,,16,8,1,10,,EC&G711&G729A,,5,ASC,Y,TRADITIO,0,S2CONN,1&&30,Y,1,2,0,0,0,0,0;


any help is appreciated.

 

[Moriendi]

So it sounds like CO trunk does not recognise the calling line ID which has been sent from the 4K, and so inserts the default number instead - 2000.

What do you expect to happen? Do you want no calling line ID, or the correct calling line ID? If you want the calling line ID to work then 4K will have to send something that the CO can recognise.