Tie from OPT 81C to BCM

[srtelengine]

I have built this PRI tie from an OPT81C(25.40b) to a BCM 4.0. When I enable the PRI and DCH I am getting a Red Alarm on the PBX side. Any suggestions for this config or even a different config would be great. We are going to CDP the numbers from the 81 to the BCM.

Thanks,

Dwayne

ADAN DCH 56
CTYP MSDL
GRP 1
DNUM 4
PORT 0
DES TEST
USR PRI
DCHL 56
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA NO
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID **
RCAP
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB
CUST 00
ROUT 87
DES TEST
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00000
NCNA YES
NCRD YES
TRO NO
CHTY BCH
CTYP CDP
INAC NO
ISAR NO
DAPC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 9487
TCPP NO
TARG 01

 

[EddieDuece]

Here is what we have;

ADAN DCH 51
CTYP MSDL
GRP 1
DNUM 1
PORT 1
DES UNUSED
USR PRI
DCHL 51
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
NASA YES
IFC SL1
SIDE NET
SEMT 1
CNEG 1
RLS ID 25
RCAP ND2 MWI
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7


TYPE RDB
CUST 00
ROUT 17
DES T1_OAC
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO YES
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN


PAGE 023

TRMB YES
STEP
ACOD 3817
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

 

[speakerboy]

Do you have mcdn networking on the bcm ?
Your pni probably needs to be 0001 in 81c.
Your bcm will need to be set as slave with sl1, you get this with the mcdn networking feature (key coded)

The bcm of course will need to be a pri trunk type.
Once these are all configured disable the bcm module and re enable.
After this make your sigo in the pbx std.

Disl your dchannel and your loop. Make sure your msdl is enabled and your dchannel auto enable and then reenable your loop.
Cross your fingers.

 

[TAnselm]

Red alarm is layer 1.
Go to the BCM, remove the cable and put a loopback plug on the end of it. See if the the T1 comes up green on the pbx. Should come up green and then the DCH drop with a message "Release Wrong Mode". If this is what you get then the problem is on the BCM side. If not check all your cabling.

 

[senk1s]

http://www142.nortelnetworks.com/bvdoc/meridian1/m1254x/P0944041.pdf

TAnselm is correct - with a good DTI card and configuration the red alarm should go away

 

[srtelengine]

Acutally it was something even more simple than any of us thought.... I forgot to do a cross over since I was going directly from the backplane to the BCM... How the simple things get by...

Thanks to all for the suggestions and help.

Dwayne