TIE call from VOIP to 11C, Only last 4 digits sent?!!??

[agpham]

Outgoing calls from Asterisk VOIP side to OPT 11 rls. 25.30 only sending last 4 digits. PRI signalling

info is showing everything,

example:
818004466444, only 6444 is being sent which is last 4 digits

Set up TIE of OPT 11 rls 25.30 TO ASTERISK VOIP SERVER
Interface: TMDI PRI NI2 ESF/B8ZS

Below are all trace and config dumps from LD 80, LD 17 CEQU/ADAN, LD 16 RDB, LD 14 BCH:

--------

TRACE SAMPLE #1 (from LD 80)

.trac 0 20 2

ACTIVE TN 004 02
ORIG 004 02 DID RMBR 20 2
TERM 006 0 00 04 RAN RMBR 3 1
DIAL DN 4444
MAIN_PM ESTD
TALKSLOT ORIG 15 TERM 43
EES_DATA:
NONE
QUEU NONE
CALL ID 0 634


---- ISDN PRA CALL (ORIG) ----
CALL REF # = 2944
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 6800
CALLED NO = 918004444444

PDCA 1 PAD 0 6 PCML MU MU


TRACE SAMPLE #2

.trac 0 20 1

ACTIVE TN 004 01
ORIG 004 01 DID RMBR 20 1
TERM NONE
TDTN 0 SLOT 22 PTY SLOT 22
DIAL DN 5828
MAIN_PM RAN
TALKSLOT NONE
EES_DATA:
NONE
QUEU RAN
CALL ID 0 557


---- ISDN PRA CALL (ORIG) ----
CALL REF # = 5632
BEARER CAP = VOICE
HLC =
CALL STATE = 7 CALL RCV
CALLING NO = 6800
CALLED NO = 91800225828

PDCA 1 PAD 0 0 PCML MU MU


--------

HERE'S THE RDB DUMP. Also, it was configured as DID because the Opt 11C has some issue with

agreeing with NI2 on TIE types. It was also discussed on Tek-Tips at

http://www.tek-tips.com/pviewthread.cfm?sqid=861830&spid=798&page=1

LD 21****
PT1000

REQ: PRT
TYPE: RDB
CUST 0
ROUT 20

TYPE RDB
CUST 00
DMOD
ROUT 20
DES ASTERISK_VOIP
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 2120
TCPP NO
PII NO
TARG 01
CLEN 3
BILN NO
OABS 0
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0


PAGE 002

DRNG NO
CDR NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO


------

HERE ARE THE BCH BUILDOUTS. Again, I had to pick TIE due to the same problem with Opt 11

supporting NI2 under TIE type.

>ld 22
PT2000

REQ prt
TYPE adan dch 6

ADAN DCH 6
CTYP TMDI
CARD 04
PORT 1
DES ASTERISK_VOIP
USR PRI
DCHL 4
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP ND2 COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

-------

HERE'S THE CEQU DUMP OF THE SPAN:

REQ prt
TYPE cequ

CEQU
MPED 8D
SUPL 000 004 008 012
016 032 036 040
044 048 064 068
072 P096
XCT 000
CONF 029 030 031 062
094 095

DLOP NUM DCH FRM LCMT YALM T1TE TRSH
TRK 03 24 D3 AMI DG2 0 00
PRI 01 23 ESF B8S FDL 0 00
02 24 ESF B8S FDL 0 00
04 23 ESF B8S FDL 0 00
MISP


If you have any ideas, please either call me at (612) 839-1040 or post reply on thread.

Thanks.


Sincerely,

Andy Pham
Manager, Information Technology Services
Automation & Control Solutions - Fire Solutions Group
Honeywell International, Inc.

Tel: (763) 391-5440
Fax: (763) 391-6980
Pager: (866) 335-9600
E-mail: andy.pham@honeywell.com

 

[johnpoole]

ld 90
prt
net
ac2 (for dial 8)
spn or npa
1800
that will send it to a rlb x

ld 86
prt
rlb
rli=x that will give you a route, a frl (cost) and a dgt y

ld 86
prt
dgt
dmi=y
that is where you can del the 1st 7 digits or not
change the dgt in the rli to 0 (a non-dgt) and you send everything you dial after the access code.. that's a2 min bars class






john poole
bellsouth business
columbia,sc