Description of the problem
At connection PRI link to the MC269AA (PRI E1), installed into the SX2K gives out a mistake of the first level. LED ST periodically blinks, the others - off.
Here are the mistakes the Aethra ISDN-tester shows:
From TE side – SYNC, CRC and RAI,
From NT side – AIS.
The PRI card was configured according to procedure of installation and configuring.
DIP switches on PRI card - 120 Ohm and NT.
Here are some Commands & Answers:
SX2K software does not show version of PRI software - empty line.
DSTAT READ 3 1 2 1 - Universal E1 not installed,
where 3 1 2 - the slot position where PRI card is installed in DSU slot of Microlight.
SH FAULT UNIVERSAL E1 CHANNEL - no faults.
CONFIG ALL - payment PRI is not displayed, card status - Nil, total circuits - 60.
The system shows mistake Critical:
- 100 % of trunks (60) are not involved
- It is not involved both links PRI
- Universal E1 card - Inactive, scan
We have made an upgrade of a card software up to version 8.2.0.11 through IMAT and through FTP according to described procedures. After updating firmware the problem was not solved.
The database of a card was configured through IMAT v7.3.0.10 via Ethernet.
There are some differences between our and standard versions in the boot-loader logging, here is our variant:
[MC269AA Boot]-: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device: flash
processor number: 0
host name:
file name: vxworks
inet on ethernet (e): 192.168.71.57
inet on backplane (b):
host inet (h):
gateway inet (g): 192.168.71.254
user (u):
ftp password (pw) (blank = use rsh
flags (f): 0x0
target name (tn):
startup script (s):
other (o): flash, c:/, ss, sx2k-eu.cmd
Bootline saved in flash
[MC269AA Boot]-:
The problem is in “sx2k-eu.cmd”, this is unacceptable by the boot loader, it writes that does not know it, therefore I do not write its name during installation procedure. Anyway it is allocated in the common folder of an upgrade and it was filled – the confirmation of successful transfer of all files to PRI card was received.
To specify files sx2k-uk.cmd or sx2k-na.cmd instead - with similar results.
May be, this is an issue?
Please help to PUSH the card into the service!
Thank you in advance.
Alex.
At connection PRI link to the MC269AA (PRI E1), installed into the SX2K gives out a mistake of the first level. LED ST periodically blinks, the others - off.
Here are the mistakes the Aethra ISDN-tester shows:
From TE side – SYNC, CRC and RAI,
From NT side – AIS.
The PRI card was configured according to procedure of installation and configuring.
DIP switches on PRI card - 120 Ohm and NT.
Here are some Commands & Answers:
SX2K software does not show version of PRI software - empty line.
DSTAT READ 3 1 2 1 - Universal E1 not installed,
where 3 1 2 - the slot position where PRI card is installed in DSU slot of Microlight.
SH FAULT UNIVERSAL E1 CHANNEL - no faults.
CONFIG ALL - payment PRI is not displayed, card status - Nil, total circuits - 60.
The system shows mistake Critical:
- 100 % of trunks (60) are not involved
- It is not involved both links PRI
- Universal E1 card - Inactive, scan
We have made an upgrade of a card software up to version 8.2.0.11 through IMAT and through FTP according to described procedures. After updating firmware the problem was not solved.
The database of a card was configured through IMAT v7.3.0.10 via Ethernet.
There are some differences between our and standard versions in the boot-loader logging, here is our variant:
[MC269AA Boot]-: c
'.' = clear field; '-' = go to previous field; ^D = quit
boot device: flash
processor number: 0
host name:
file name: vxworks
inet on ethernet (e): 192.168.71.57
inet on backplane (b):
host inet (h):
gateway inet (g): 192.168.71.254
user (u):
ftp password (pw) (blank = use rsh
flags (f): 0x0
target name (tn):
startup script (s):
other (o): flash, c:/, ss, sx2k-eu.cmd
Bootline saved in flash
[MC269AA Boot]-:
The problem is in “sx2k-eu.cmd”, this is unacceptable by the boot loader, it writes that does not know it, therefore I do not write its name during installation procedure. Anyway it is allocated in the common folder of an upgrade and it was filled – the confirmation of successful transfer of all files to PRI card was received.
To specify files sx2k-uk.cmd or sx2k-na.cmd instead - with similar results.
May be, this is an issue?
Please help to PUSH the card into the service!
Thank you in advance.
Alex.