Tannoy System

[bombaytelecom]

Not sure if this is possible but on a previous phone system at a previous employment you could enter a feature code and could make announcements over the speakers on all the phones (i belive they have to have the feature enabled on the handsets/ be in a group similar to pickup groups. I was just wondering if anyone knows if it is possible on the Option 61c?

Meridian Option 61C
Symposium v 4.5
NICE Dictaphone Recording

 

[cmawbey]

Feature description
The Meridian 1 provides switching access and trunk circuit interface to a
customer-supplied speaker or radio paging equipment. Paging equipment is
accessed by dial access or a Page key on Attendant Consoles. Telephones
cannot be assigned a Page key and must dial access this feature.
Attendant Consoles using the Page key preempt telephones having only dial
access. Telephones preempted by the attendant are disconnected and must
re-access the paging trunk.
Page 2504 of 3156 Paging
553-3001-306 Standard 10.00 January 2002
Time Forced Disconnect (TFD), provides a variable timer to force disconnect
Paging trunks. The timer is defined on a route basis to limit the time a user
can keep a Paging trunk seized. When the timer expires, the call is
disconnected from the trunk. The trunk is disconnected when the Time
Forced Disconnect (TFD) timer expires in all cases, regardless of the status
of the trunk at the time. Timing starts as soon as the trunk is seized (not when
the call is established), so the timer must allow some delay for connection
time.
The Time Forced Disconnect timer is used on the following trunk types:
Operating parameters
Station dial access to the Paging trunk is restricted by the Trunk Group
Access Restriction (TGAR) code entered in LD 10 or LD 11.
Unique access codes are required for each Paging route.
Unique feature keys are assigned for each Paging route.
All Zone Paging is not available with Meridian 1, unless the customerprovided
paging equipment is equipped with separate “all-zone” input.
The following requirements apply to Time Forced Disconnect (TFD) feature:
• The timer can only be assigned on a route basis and not to individual
trunks. All trunks in a route have the same timer value.
• After a timer value is changed, it does not take effect on a given trunk
until that trunk is released and seized again.
• Changing a timer value to zero (0) effectively removes the TFD timer
from all the trunks in that route.
• The range of the timer is one hour, in 30-second increments (0–3600).
The TFD timer is independent of all other timers.
• COT Central Office
• DIC Dictation
• FEX Foreign Exchange
• PAG Paging trunks
• TIE Tie direct lines
• WAT Wide Area Telephone Service
Paging Page 2505 of 3156
Features and Services
Trunks forced off by TFD are disconnected normally, accompanied by an
error message (ERR4054) output on the system terminal. The error message
identifies the Originating Terminal Number (TN), Terminating Terminal
Number (TN), date, and time for the following trunk types:
• Analog trunks
• Digital Trunk Interface (DTI) trunks, and
• ISDN Integrated Service Links (ISL)/Primary Rate Interface (PRI)
trunks.
Feature interactions
Call Forward All Calls
Calls that originate on a TIE trunk to a telephone that is redirected to a paging
route are blocked.
Conference
Paging trunks cannot be used in a conference call.
Multi-Party Operations
Users of analog (500/2500 type) telephones cannot make a consultation call
while connected to a paging trunk.
Private Line Routes
Route 31 can be assigned as a paging route.
Feature packaging
This feature is included in base X11 System Software.
Feature implementation


Task summary list
The following is a summary of the tasks in this section.
1 LD 16 – Add or change a Paging trunk route access code and restriction
group numbers.

2 LD 16 – Define the timer for the Time Forced Disconnect feature.

3 LD 14 – Add or change a Paging trunk within the Paging trunk route.

Page 2506 of 3156 Paging

553-3001-306 Standard 10.00 January 2002

4 LD 12 – Assign Paging key for an Attendant Console. No programming
is required to allow the attendant dial access to Paging.
5 LD 10 – Allow or deny dial access to Paging for analog (500/2500 type)
telephones.
6 LD 11 – Allow or deny dial access to Paging for Meridian 1 proprietary
telephones.

LD 16 – Add or change a Paging trunk route access code and restriction group numbers.
LD 16 – Define the timer for the Time Forced Disconnect feature.

Prompt Response Description
REQ CHG Change.
TYPE RDB Route Data Block.
CUST 0-99
ROUTE 0-511 1-127Route number.For Option 11C.
TKTP PAG Paging trunk route.
ICOG OGT Outgoing trunk.
ACOD xxx...x Trunk route access code (if the Directory Number
Expansion package is equipped, this access code can have
up to seven digits).
TARG 1-31 Trunk access restriction group number.

Prompt Response Description
REQ CHG Change.
TYPE RDB Route Data Block.
CUST 0-99
0-31Customer number.For Option 11C.

Paging Page 2507 of 3156
Features and Services









LD 14 – Add or change a Paging trunk within the Paging trunk route.
ROUTE 0-511
0-127 Route number. For Option 11C.
CNTL (NO) YES Changes to controls or timers (default is NO).
TIMR TFD xxxx TFD timer, where :xxxx = 0-(30)-3600 seconds, in 30-second increments.

Prompt Response Description
REQ CHG Change.
TYPE PAG Paging trunk.
TN l s c u
c u Terminal Number.For Option 11C.

XTRK XUT XEM Universal Trunk Card (NT8D14), E&M Trunk Card
(NT8D15). Prompted only for superloops and the first unit
on the card.

CUST 0-99 Customer number.
SIGL DX2
DX4
EAM
EM4
LDR
OAD
DX signalling (two-wire) – QPC71 only.
DX signalling (four-wire) – QPC71 and NT8D15.
E&M signalling (two-wire) – QPC71 and NT8D15.
E&M signalling (four-wire) – QPC71 and NT8D15.
Loop dial repeating – QPC71 and NT8D14/15.
Outgoing automatic, incoming dial – QPC71, NT8D14/15.
STRO IMM
WNK
DDL
Immediate start outgoing.
Wink start outgoing.
Delay dial outgoing.
SUPN (NO) YES Answer and disconnect supervision required.

Page 2508 of 3156 Paging
553-3001-306 Standard 10.00 January 2002

LD 12 – Assign Paging key for an Attendant Console. No programming is required to allow the
attendant dial access to Paging.

LD 10 – Allow or deny dial access to Paging for analog (500/2500 type) telephones.
Prompt Response Description
REQ CHG Change.
TYPE ATT 1250 2250 Console type.
TN l s c u

KEY xx PAG yyy...y Paging key, where:
xx = key number (0-9 on M1250, 0-19 on M2250), and
yy...y = access code of Paging trunk route.

Prompt Response Description
REQ: CHG Change.
TYPE: 500 Telephone type.
TN l s c u
c u
Terminal Number.
For Option 11C.
TGAR xx Allow/deny access to Paging trunk.

Paging Page 2509 of 3156




LD 11 – Allow or deny dial access to Paging for Meridian 1 proprietary telephones.
Prompt Response Description
REQ: CHG Change.
TYPE: aaaa Telephone type, where:
aaaa = SL1, 2006, 2008, 2009, 2016, 2018, 2112, 2216,
2317, 2616, or 3000.
TN l s c u
c u
Terminal Number.
For Option 11C.
TGAR xx Allow/deny access to Paging trunk.

 

[Firebird Scrambler]

I'm guessing that your previous system was something like a Nortel Norstar which could do that function.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[bombaytelecom]

potentially it could have been.. it was at the start of my career where i wasnt really involved in Telephony. Thanks for the information Giblett.. a little bit confused when it is talking about trunks is it refering to idividual Dgtl Line cards?

Meridian Option 61C
Symposium v 4.5
NICE Dictaphone Recording

 

[johnpoole]

s digital line card is not in that call path.. an analog trunk card will interface between a Valsomm paging adapter and your amp/speakers.. all of that is external to the stations or station speakers.. since this system can get so large, a power supply to push all station speakers would be to large and expensive to use.

i use a single phone on auto answer to page the switch room, with 4 full time techs, instead of calling each desk, anyone that knows the number can page via dialing the dn on key 0 of a 2616 with auto answer active

john poole
bellsouth business
columbia,sc

 

[GHTROUT]

Gibblett was referring to paging over the office or overhead speakers. Not over the telephone speakers.

There are workarounds, but I suggest you avoid them thread798-1509423


--
Nortel Resources at GHTROUT.com | Connect with me on LinkedIn
--

 

[johnpoole]

i added a faq with a paging rdb and trunk, hope it helps

john poole
bellsouth business
columbia,sc