I have an Origin200 with single processor (225 MHZ).
I would like to swap it out with a dual 180 MHZ module.
The machine sees the new hardware.
At the prompt (5), I undertake the following: resetenv followed by: update
I start the system and it boots but then fails miserably (see below).
Do I need to do anything else on the command line before booting?
Best regards
------------------------------------------------------
IP27 PROM SGI Version 6.27 built 12:25:37 PM Mar 18, 1999
using BaseIO nic
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering CrayLink connectivity .........
Local hub CrayLink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30372 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/0/slot/MotherBoard
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.27 built 12:24:50 PM Mar 18, 1999 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Walking SCSI Adapter 0 (/hw/module/1/slot/MotherBoard), (pci id 0)
1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/MotherBoard), (pci id 1)
1- 2- 3- 4- 5- 6+ 7- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ...............
***Warning: Found a different board in module 1, slot MotherBoard,
Previous barcode was DEM675, New barcode is DFP691
Found new component
Found new component
***Warning: Board in module 2, slot MotherBoard is missing or disabled
It previously contained a node-board, barcode HXM297 laser 310b00
***Warning: Board in module 2, slot MotherBoard is missing or disabled
It previously contained a BASEIO board, barcode HTG232 laser 308594
DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 2048 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
>> hinv
System SGI-IP27
2 225 MHz IP27 Processors
Main memory size: 2048 Mbytes
Integral SCSI controller 0
Integral SCSI controller 1
Integral Fast Ethernet
IOC3 serial port
Disk drive: unit 1 on SCSI Controller 0, (dksc(0,1,0))
Disk drive: unit 2 on SCSI Controller 0, (dksc(0,2,0))
Disk drive: unit 3 on SCSI Controller 0, (dksc(0,3,0))
Disk drive: unit 4 on SCSI Controller 0, (dksc(0,4,0))
Disk drive: unit 5 on SCSI Controller 0, (dksc(0,5,0))
Disk drive: unit 6 on SCSI Controller 0, (dksc(0,6,0))
CDROM: unit 6 on SCSI Controller 1, (cdrom(1,6,7))
>> resetenv
>> update
Updated new configuration. Wrote 2 records.
>>
Starting up the system...
WARNING: Check the date to make sure it is correct
WARNING: Check the date to make sure it is correct
IRIX Release 6.5 IP27 Version 04101930 System V - 64 Bit
Copyright 1987-2002 Silicon Graphics, Inc.
All Rights Reserved.
Setting rbaud to 19200
WARNING: Check the date to make sure it is correct
The system is coming up.
/etc/rc2.d/S30network[375]: :if2name=: not found
/etc/rc2.d/S30network[375]: :if2addr=: not found
/usr/freeware/apache/sbin/apachectl start: httpd started
Starting FlashNet batchd daemon...
Starting FlashNet Globald...
FlashNet Batch Restore Daemon v1.4 (64bit)
Running up at Sat Jan 24 10:43:28 2004
Process ID 928
Starting FlashNet Scheduler...
FlashNet Scheduler 5.9.1 (64 bit)
Running up at Sat Jan 24 10:43:29 2004
Process ID 938
K-Talk kernel module loaded
AppleTalk Services: atconfig nbpd epd timeserver spoolserv ksd xnetdd jgui fpod
papserver papserver papserver papserver papserver papserver.
Starting mysqld daemon with databases from /usr/etc/venture/data
SGI console login: root
Password:
IRIX Release 6.5 IP27 SGI
Copyright 1987-2002 Silicon Graphics, Inc. All Rights Reserved.
Last login: Fri Jan 23 22:05:11 CET 2004 by Administrator@192.50.50.222
You have mail.
TERM = (vt100)
SGI 1# bash
bash-2.05b# HARDWARE ERROR STATE:
End Hardware Error Sta e
++FRU ANALYSIS BEGIN
++
++
++ FRU Analysis Summary
++
++ Software : 90%
++
++FRU ANALYSIS END
PANIC: CPU 1: TLBMISS: KERNEL FAULT
PC: 0xc00000000011299c ep: 0xa800000001637d58
EXC code:8, `Read TLB Miss '
Bad addr: 0xc0000fc000000020, cause: 0x8<CE=0
Dumping to /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/0/scsi_ctlr/0/target/1
/lun/0/disk/partition/1/block at block 0, space: 0x2000 pages
Waiting 5 seconds for I/O processor.
CPU 0 is the I/O processor.
Dumping low memory...
Dumping static kernel pages......
Dumping pfdat pages....
Dumping backtrace pages...
Dumping dynamic kernel pages..........
Dumping buffer pages....
Dumping remaining in-use pages.................................
Dumping hub information .....
Available dump space depleted.
Reboot started from CPU 1
CPU 1 rebooting
IP27 PROM SGI Version 6.27 built 12:25:37 PM Mar 18, 1999
using BaseIO nic
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering CrayLink connectivity .........
Local hub CrayLink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30369 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/1/slot/MotherBoard
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.27 built 12:24:50 PM Mar 18, 1999 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Walking SCSI Adapter 0 (/hw/module/1/slot/MotherBoard), (pci id 0)
1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/MotherBoard), (pci id 1)
1- 2- 3- 4- 5- 6+ 7- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 2048 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
Starting up the system...
IRIX Release 6.5 IP27 Version 04101930 System V - 64 Bit
Copyright 1987-2002 Silicon Graphics, Inc.
All Rights Reserved.
Setting rbaud to 19200
The system is coming up.
/etc/rc2.d/S30network[375]: :if2name=: not found
/etc/rc2.d/S30network[375]: :if2addr=: not found
System went down at Sat Jan 24 10:44:06 2004
savecore: Saving 134201344 bytes of image in /var/adm/crash/vmcore.0.comp
/usr/freeware/apache/sbin/apachectl start: httpd started
Starting FlashNet batchd daemon...
Starting FlashNet Globald...
FlashNet Batch Restore Daemon v1.4 (64bit)
Running up at Sat Jan 24 10:51:46 2004
Process ID 1120
Starting FlashNet Scheduler...
FlashNet Scheduler 5.9.1 (64 bit)
Running up at Sat Jan 24 10:51:46 2004
Process ID 1130
K-Talk kernel module loaded
AppleTalk Services: atconfig nbpd epd timeserver spoolserv ksd xnetdd jgui fpod
papserver papserver papserver papserver papserver papserver.
Starting mysqld daemon with databases from /usr/etc/venture/data
SGI console login: root
Password:
IRIX Release 6.5 IP27 SGI
Copyright 1987-2002 Silicon Graphics, Inc. All Rights Reserved.
Last login: Fri Jan 23 22:05:11 CET 2004 by Administrator@192.50.50.222
You have mail.
TERM = (vt100)
/usr/etc/amstart: Error: No availmon configuration has been found. You might nee
d to execute amconfig to setup availmon configuration
/usr/etc/amstart[426]: test: argument expected
SGI 1# HARDWARE ERROR STATE:
End Hardware Error Sta e
++FRU ANALYSIS BEGIN
++
++
++ FRU Analysis Summary
++
++ Software : 90%
++
++FRU ANALYSIS END
PANIC: CPU 0: KERNEL FAULT
PC: 0xc00000000016079c ep: 0xa800000000527e00
EXC code:16, `Read Address Error '
Bad addr: 0x305070004020a1c, cause: 0x10<CE=0
Dumping to /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/0/scsi_ctlr/0/target/1
/lun/0/disk/partition/1/block at block 0, space: 0x2000 pages
Waiting 5 seconds for I/O processor.
CPU 1 is the I/O processor.
Dumping low memory...
Dumping static kernel pages......
Dumping pfdat pages....
Dumping backtrace pages...
Dumping dynamic kernel pages..........
Dumping buffer pages....
Dumping remaining in-use pages..................................................
....................................................................
Available dump space depleted.
Reboot started from CPU 0
CPU 0 rebooting
Restarting the machine...
I would like to swap it out with a dual 180 MHZ module.
The machine sees the new hardware.
At the prompt (5), I undertake the following: resetenv followed by: update
I start the system and it boots but then fails miserably (see below).
Do I need to do anything else on the command line before booting?
Best regards
------------------------------------------------------
IP27 PROM SGI Version 6.27 built 12:25:37 PM Mar 18, 1999
using BaseIO nic
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering CrayLink connectivity .........
Local hub CrayLink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30372 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/0/slot/MotherBoard
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.27 built 12:24:50 PM Mar 18, 1999 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Walking SCSI Adapter 0 (/hw/module/1/slot/MotherBoard), (pci id 0)
1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/MotherBoard), (pci id 1)
1- 2- 3- 4- 5- 6+ 7- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ...............
***Warning: Found a different board in module 1, slot MotherBoard,
Previous barcode was DEM675, New barcode is DFP691
Found new component
Found new component
***Warning: Board in module 2, slot MotherBoard is missing or disabled
It previously contained a node-board, barcode HXM297 laser 310b00
***Warning: Board in module 2, slot MotherBoard is missing or disabled
It previously contained a BASEIO board, barcode HTG232 laser 308594
DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 2048 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
>> hinv
System SGI-IP27
2 225 MHz IP27 Processors
Main memory size: 2048 Mbytes
Integral SCSI controller 0
Integral SCSI controller 1
Integral Fast Ethernet
IOC3 serial port
Disk drive: unit 1 on SCSI Controller 0, (dksc(0,1,0))
Disk drive: unit 2 on SCSI Controller 0, (dksc(0,2,0))
Disk drive: unit 3 on SCSI Controller 0, (dksc(0,3,0))
Disk drive: unit 4 on SCSI Controller 0, (dksc(0,4,0))
Disk drive: unit 5 on SCSI Controller 0, (dksc(0,5,0))
Disk drive: unit 6 on SCSI Controller 0, (dksc(0,6,0))
CDROM: unit 6 on SCSI Controller 1, (cdrom(1,6,7))
>> resetenv
>> update
Updated new configuration. Wrote 2 records.
>>
Starting up the system...
WARNING: Check the date to make sure it is correct
WARNING: Check the date to make sure it is correct
IRIX Release 6.5 IP27 Version 04101930 System V - 64 Bit
Copyright 1987-2002 Silicon Graphics, Inc.
All Rights Reserved.
Setting rbaud to 19200
WARNING: Check the date to make sure it is correct
The system is coming up.
/etc/rc2.d/S30network[375]: :if2name=: not found
/etc/rc2.d/S30network[375]: :if2addr=: not found
/usr/freeware/apache/sbin/apachectl start: httpd started
Starting FlashNet batchd daemon...
Starting FlashNet Globald...
FlashNet Batch Restore Daemon v1.4 (64bit)
Running up at Sat Jan 24 10:43:28 2004
Process ID 928
Starting FlashNet Scheduler...
FlashNet Scheduler 5.9.1 (64 bit)
Running up at Sat Jan 24 10:43:29 2004
Process ID 938
K-Talk kernel module loaded
AppleTalk Services: atconfig nbpd epd timeserver spoolserv ksd xnetdd jgui fpod
papserver papserver papserver papserver papserver papserver.
Starting mysqld daemon with databases from /usr/etc/venture/data
SGI console login: root
Password:
IRIX Release 6.5 IP27 SGI
Copyright 1987-2002 Silicon Graphics, Inc. All Rights Reserved.
Last login: Fri Jan 23 22:05:11 CET 2004 by Administrator@192.50.50.222
You have mail.
TERM = (vt100)
SGI 1# bash
bash-2.05b# HARDWARE ERROR STATE:
End Hardware Error Sta e
++FRU ANALYSIS BEGIN
++
++
++ FRU Analysis Summary
++
++ Software : 90%
++
++FRU ANALYSIS END
PANIC: CPU 1: TLBMISS: KERNEL FAULT
PC: 0xc00000000011299c ep: 0xa800000001637d58
EXC code:8, `Read TLB Miss '
Bad addr: 0xc0000fc000000020, cause: 0x8<CE=0
Dumping to /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/0/scsi_ctlr/0/target/1
/lun/0/disk/partition/1/block at block 0, space: 0x2000 pages
Waiting 5 seconds for I/O processor.
CPU 0 is the I/O processor.
Dumping low memory...
Dumping static kernel pages......
Dumping pfdat pages....
Dumping backtrace pages...
Dumping dynamic kernel pages..........
Dumping buffer pages....
Dumping remaining in-use pages.................................
Dumping hub information .....
Available dump space depleted.
Reboot started from CPU 1
CPU 1 rebooting
IP27 PROM SGI Version 6.27 built 12:25:37 PM Mar 18, 1999
using BaseIO nic
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering CrayLink connectivity .........
Local hub CrayLink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30369 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/1/slot/MotherBoard
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.27 built 12:24:50 PM Mar 18, 1999 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Walking SCSI Adapter 0 (/hw/module/1/slot/MotherBoard), (pci id 0)
1+ 2+ 3+ 4+ 5+ 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 6 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/MotherBoard), (pci id 1)
1- 2- 3- 4- 5- 6+ 7- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 2048 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
Starting up the system...
IRIX Release 6.5 IP27 Version 04101930 System V - 64 Bit
Copyright 1987-2002 Silicon Graphics, Inc.
All Rights Reserved.
Setting rbaud to 19200
The system is coming up.
/etc/rc2.d/S30network[375]: :if2name=: not found
/etc/rc2.d/S30network[375]: :if2addr=: not found
System went down at Sat Jan 24 10:44:06 2004
savecore: Saving 134201344 bytes of image in /var/adm/crash/vmcore.0.comp
/usr/freeware/apache/sbin/apachectl start: httpd started
Starting FlashNet batchd daemon...
Starting FlashNet Globald...
FlashNet Batch Restore Daemon v1.4 (64bit)
Running up at Sat Jan 24 10:51:46 2004
Process ID 1120
Starting FlashNet Scheduler...
FlashNet Scheduler 5.9.1 (64 bit)
Running up at Sat Jan 24 10:51:46 2004
Process ID 1130
K-Talk kernel module loaded
AppleTalk Services: atconfig nbpd epd timeserver spoolserv ksd xnetdd jgui fpod
papserver papserver papserver papserver papserver papserver.
Starting mysqld daemon with databases from /usr/etc/venture/data
SGI console login: root
Password:
IRIX Release 6.5 IP27 SGI
Copyright 1987-2002 Silicon Graphics, Inc. All Rights Reserved.
Last login: Fri Jan 23 22:05:11 CET 2004 by Administrator@192.50.50.222
You have mail.
TERM = (vt100)
/usr/etc/amstart: Error: No availmon configuration has been found. You might nee
d to execute amconfig to setup availmon configuration
/usr/etc/amstart[426]: test: argument expected
SGI 1# HARDWARE ERROR STATE:
End Hardware Error Sta e
++FRU ANALYSIS BEGIN
++
++
++ FRU Analysis Summary
++
++ Software : 90%
++
++FRU ANALYSIS END
PANIC: CPU 0: KERNEL FAULT
PC: 0xc00000000016079c ep: 0xa800000000527e00
EXC code:16, `Read Address Error '
Bad addr: 0x305070004020a1c, cause: 0x10<CE=0
Dumping to /hw/module/1/slot/MotherBoard/node/xtalk/8/pci/0/scsi_ctlr/0/target/1
/lun/0/disk/partition/1/block at block 0, space: 0x2000 pages
Waiting 5 seconds for I/O processor.
CPU 1 is the I/O processor.
Dumping low memory...
Dumping static kernel pages......
Dumping pfdat pages....
Dumping backtrace pages...
Dumping dynamic kernel pages..........
Dumping buffer pages....
Dumping remaining in-use pages..................................................
....................................................................
Available dump space depleted.
Reboot started from CPU 0
CPU 0 rebooting
Restarting the machine...