Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
SV8100 DTMF
- Thread starter Neaxtec
- Start date
I have not but NEC has touted this training routine for some time:
Program 90-68-01 performs a series of tests on the selected lines and auto adjusts it to the line's levels.
To do this you must do the following from a telephone:
Enter system programming by pressing Speaker, then dialing #, *, #, *.
Password is 12345678, then press the Transfer Key. Next enter 9068 to go to program 90-68-01, then press select.
At the "Adjustment Start _ " Prompt enter the line number of your first analog trunk, then press Transfer.
The system will then run a series of tests on that line. Allow the tests to complete. If the line is not an analog line or if the line currently does not have dial tone, you will be returned with "Error".
Once the tests are complete, you will be presented with "Copy? (1 if Yes)" if you wish to copy the new settings the system has automatically set for this line to your other lines, enter a 1 and then press Transfer. If not, simply press Transfer, then the Answer key several times to back up to a blinking curser on the display and then press the Speaker key to exit.
It is recommended to run this on each line individually in place of copying the settings since it is possible for each analog lines to have different physical characteristics.
Once the test/tests have been completed the Trunk Blade MUST be reset for the changes to take place.
This procedure should be run in the following cases:
Upon new install of a SV8100 / SV9100, once the system is installed onsite with the analog lines installed.
Anytime the system is moved to a new site, once the lines are re-installed at the new location.
Anytime the line source changes such as changing over to a new provider.
Anytime an additional line is added.
This only applies to analog lines.
Running these procedures often resolves many issues such as echo, poor Speakerphone quality when on outside lines and DTMF reception issues related to an Auto Attendant.
Conditions:
All phones and trunks must be idle in order to perform the Side Tone Auto Setup test. If any phone or trunk is in use, "Busy" will be displayed when trying to run 90-68-01.
All phones will become unresponsive while the Side Tone Auto Setup tests are running.
Program 90-68-01 performs a series of tests on the selected lines and auto adjusts it to the line's levels.
To do this you must do the following from a telephone:
Enter system programming by pressing Speaker, then dialing #, *, #, *.
Password is 12345678, then press the Transfer Key. Next enter 9068 to go to program 90-68-01, then press select.
At the "Adjustment Start _ " Prompt enter the line number of your first analog trunk, then press Transfer.
The system will then run a series of tests on that line. Allow the tests to complete. If the line is not an analog line or if the line currently does not have dial tone, you will be returned with "Error".
Once the tests are complete, you will be presented with "Copy? (1 if Yes)" if you wish to copy the new settings the system has automatically set for this line to your other lines, enter a 1 and then press Transfer. If not, simply press Transfer, then the Answer key several times to back up to a blinking curser on the display and then press the Speaker key to exit.
It is recommended to run this on each line individually in place of copying the settings since it is possible for each analog lines to have different physical characteristics.
Once the test/tests have been completed the Trunk Blade MUST be reset for the changes to take place.
This procedure should be run in the following cases:
Upon new install of a SV8100 / SV9100, once the system is installed onsite with the analog lines installed.
Anytime the system is moved to a new site, once the lines are re-installed at the new location.
Anytime the line source changes such as changing over to a new provider.
Anytime an additional line is added.
This only applies to analog lines.
Running these procedures often resolves many issues such as echo, poor Speakerphone quality when on outside lines and DTMF reception issues related to an Auto Attendant.
Conditions:
All phones and trunks must be idle in order to perform the Side Tone Auto Setup test. If any phone or trunk is in use, "Busy" will be displayed when trying to run 90-68-01.
All phones will become unresponsive while the Side Tone Auto Setup tests are running.
- Status