Strange - can get to one server, but not the other??

[Ferbert]

Hello!
I have a little PIX 506e that works great. Here is the scenario.

The way it used to be: I have a single server that needed access from the outside. I have a 5 pack of IP addresses that starts at 71.12.111.218. I nat the outside 71.12.111.219 to my inside server address 192.168.1.23 for http, smtp, and RDP. The old config worked great - and still does.

The way I need it now: I have a new server - I need to nat 71.12.111.220 to 192.168.1.31 for http, smtp, and rdp. I want to keep the config for the old server, too. The new sh run is below. I cannot get to the new server on any ports. HELP!

PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password z41nzcQp3UU1GsZk encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname ferbpix
domain-name ferbert.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 192.168.1.23 ferbweb
name 71.12.111.219 ferbwebpub
name 192.168.1.31 ferbmail
name 71.12.111.220 ferbmailpub
access-list outside_in permit tcp any host ferbwebpub eq www
access-list outside_in permit tcp any host ferbwebpub eq smtp
access-list outside_in permit udp any host ferbwebpub eq www
access-list outside_in permit udp any host ferbwebpub eq 3389
access-list outside_in permit tcp any host ferbwebpub eq 3389
access-list outside_in permit tcp any host ferbmailpub eq www
access-list outside_in permit tcp any host ferbmailpub eq smtp
access-list outside_in permit udp any host ferbmailpub eq www
access-list outside_in permit udp any host ferbmailpub eq 3389
access-list outside_in permit tcp any host ferbmailpub eq 3389
access-list inside_out permit ip any any
access-list inside_out permit icmp any any
pager lines 24
icmp permit any inside
mtu outside 1500
mtu inside 1500
ip address outside 71.12.111.218 255.255.255.248
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) ferbwebpub ferbweb netmask 255.255.255.255 0 0
static (inside,outside) ferbmailpub ferbmail netmask 255.255.255.255 0 0
access-group outside_in in interface outside
access-group inside_out in interface inside
route outside 0.0.0.0 0.0.0.0 71.12.111.217 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout sip-disconnect 0:02:00 sip-invite 0:03:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 inside
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd auto_config outside
terminal width 80

Any help woud be appreciated. Thanks!

 

[unclerico]

This new server, it is configured properly? Have you tried enabling logging on the pix and watch traffic?

 

[Viconsul]

Hello,

Are you still experiencing problems connecting from outside to your server?
If so, you might want to check your software firewall on the server e.g
windows firewall and also go over your server network configurations.
The cisco 506e configuration looks okay.

HTH
Viconsul