Still no inbound...

[mjwilson12379]

Hello all. I have verified up and down our system. Brand new Magix. 100DCD w/ full PRI. THe circuit seems to be stable, the D channel doesnt drop or anything. Yet, we are unable to get any inbound calls. Below is the config.

DMS-100, B8ZS, ESF, etc, etc.

Every now and then, I see a '7002' SVC STATE INCONSIST in teh log. THanks so much for everyones help.

PRI INFORMATION



Slot 2 Switch: DMS-100

System: By line

BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 2 DMS-OUTWATS By Dial Plan

Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1

Line PhoneNumber NumberToSend
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823

Network Selection Table

Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***

Special Service Table

Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 0 0 0 0 0 0 0 0
Operator: none none none none none none none none
Type of Number: I I I N N N N N
Digits to Delete: 0 0 0 0 0 0 0 0

Call-By-Call Service Table

Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
PRI INFORMATION


Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0

Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0

Dial Plan Routing Table

Entry Number: 0 1 2 3
NtwkServ: Any service Any service
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:

------------------
Michael Wilson
Dir. of I.T.
REMAX Allegiance

 

[jinxs]

are they sending you the right protocol for the DMS-100?There is an aswsome FAQ in the legend/magix forum for troubleshooting a PRI, look it up. TTT posted it,it had helped me many of times.

 

[redphone]

You need to set your NtwkServ to Call by Call. It looks like you have it set to DMS-OUTWATS. Also in your Dial plan routing table, you should specify how many digits are expected, and what pattern to match.

Hope this helps.

 

[jinxs]

That is of course your CO is utilizing the call by call service. Most of them do but it does have to be ordered when setting up the PRI.