Stat PRI Channels 1

[Voicedataman]

If I STAT under LD60 on my Option 61 C, it shows the status of the my bothway isdn30(PRI) channels ...nice.
If I do the same on my Option81C, it just shows me the status of the 4 TIE isdn30's that I have.
I also have 8 ISDN30's for incoming calls..Do you know how I can show the status of my incoming and outgoing PRI's
Example shown..
.stat 68


PRI2 LOOP 68 - ENBL
REF CLK: DSBL
SERVICE RESTORE: YES
ALARM STATUS: ACCEPTABLE
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - IDLE TIE VOD *
CH 25 - IDLE TIE VOD * CH 26 - IDLE TIE VOD *
CH 27 - IDLE TIE VOD * CH 28 - IDLE TIE VOD *
CH 29 - IDLE TIE VOD * CH 30 - IDLE TIE VOD *
CH 31 - DCH 12

 

[johnpoole]

all pri's stat in 60, just the stat command, prt your cequ in ld 22, that gives you a list of all config'ed pri, t1's supl...etc

john poole
bellsouth business
columbia,sc

 

[Voicedataman]

Thanks! I have attached prt.
Do you if there is a way of displaying whether the channels are/busy/idle/oos on the PRI's.
EQU
MPED 8D
TERM
REMO
TERD 040 041
REMD
TERQ
REMQ
SUPL 004 020 036 052
072 N156
SUPC
SUPF
DDCS 014 015 030 031
034 035 048 049
062 063 066 067
082 083 086 087
DTCS
XCT 008 016 032 050
064 080
TDS * 008 * 016 * 032 * 050
* 064 * 080
CONF * 009 * 017 * 033 * 051
* 065 * 081
MFSD * 008 * 016 * 032 * 050
* 064 * 080
PRI2 068 069 078 079
APVL
DTI2
MISP 070
EXT0 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
EXT1 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 000 016 000 000 000 32 080

 

[Voicedataman]

I guess it's probably because they are DASS not ISDN30??

 

[johnpoole]

you can stat an entire route, start by printing a simple tn, from that your get (rtmb) route and member, ld 21 prt rdb for that route, you need the acod (access code) in load 80 trac 0 acod..(0 for cust) you don't get who they are connected to but you get which ones are busy, if you need details use the trac x x x x command or trad x x for a dig trunk.

john poole
bellsouth business
columbia,sc

 

[Voicedataman]

John,

That was exactly what I was looking for! Thanks...

Coming from an Avaya Definity background, I know what I want to do but it's a bit strange having to load overlays!!!!

 

[johnpoole]

takes some getting used to, rolm mitel nec etc is the same way, i think thats a carry over from trying to use 3 letters for all commands, the same command can be used in different loads for different functions, early releases you had to print tn's in 21 and dns in 20 build ann in 10 and dig in 11 and stat in 32, it is getting better but a big jump from avaya, sorta put the T back in tech

john poole
bellsouth business
columbia,sc