SMDR X BC10

[MD6]

Hi all,

I have md110 bc10 and i have smdr-v24-interface license. In the lidap command i see allowed=1 and used=1, but i dont have cil programed. see below...

LICENCE TAG ALLOWED USED
SMDR-V24-INTERFACE 1 1

cldfp;
FILE ADMINISTRATION DATA

FILE STATE IODEV USER DEVICE STATE PRIORITY

END

clinp;
NOT ACCEPTED
NO HEADER ASSIGNED

edeqp;
NOT ACCEPTED
DEV
NOT INITIATED
edfip;
NOT ACCEPTED
FILE
NOT INITIATED


thanks all,

 

[lancbomb]

I think that just means that the interface is ther and ready to go but it is not programmed up.

hence no clinp !

 

[MD6]

Hi,

I try

IOEQI:EQU=1-0-60-3,IODEV=SMDR,USAGE=OUT;
EXECUTED

CLDFI:FILE=SMDR,IODEV=SMDR,USER=NONE,PRIO=C;
NOT ACCEPTED
LICENSE IS NOT AVAILABLE

tks

 

[lancbomb]

The card is there but not the license for the CIL programming.

do a LIDAP print pls

 

[MD6]

Hi,

lidap command print:

LICENCE TAG ALLOWED USED
SMDR-V24-INTERFACE 1 1


tks

 

[doktor]

Hi MD6

You should be able to see something when using the commands
EDFIP;, CLDFP; and CLINP;
It seems that your license has not been correctly activated.
Try to send the command SFCEI;
Or resend your license file by LIDAI...
An other issue could be restart the programmes for CIL.
BR doktor

 

[MD6]

Hi Doktor,

I tryed sfcei, lidai and I restart PABX, but the lidap print out is:

LICENCE TAG ALLOWED USED
SMDR-V24-INTERFACE 1 1

sorry for my bad english,

thanks...

 

[doktor]

MD6

Try to restart the following program in the mentioned LIMs:

EDP in one LIM in the exchange
FAM2 in one LIM in the exchange
SIP in the same LIM as the SIU board
CLHH in one LIM in the exchange
CLOM in one LIM in the exchange
CLOP in every LIM
CLP in every LIM

Restart with:
RFPUI:UNIT=,LIM=;
also:
SFPUI:UNIT=,LIM=;

Post a printout of the ALLOP; here.
It seems that something has "hung up"...
BR doktor

 

[fidde]

Your license database have been corupted. Make a fault report to Ericsson and they fix it through modem.

 

[doktor]

MD6

You could - before you report this fault - try to
restart the progrm LISH in LIM=1.

RFPUI:UNIT=LISH ,LIM=1;

This can sometimes help if the license server is blocked.

BR doktor

 

[MD6]

Hi all,

I try RFPUI:UNIT=LISH ,LIM=1; but not ok.

I try removed units for cil facility(clom, sip, ...) and not ok too.
the lidap command only print´s:
LICENCE TAG ALLOWED USED
SMDR-V24-INTERFACE 1 1

Tks,

 

[mdman]

In your CLDFI command the USER should be CIL-x, where x is 0-99.
I don't know if that will solve your problem though.

 

[MD6]

Hi,

My problem is license used, but not programed.

tks,

md6

 

[whosrdaddy]

are you sure it isn't programmed (check ioddp/ioncp)

--------------------------------------
What You See Is What You Get

 

[NIUX]

Can you print the following:
CADAP;
CNPIP:UNIT=CLHH;
CNPIP:UNIT=CLOM;
PCLOP:UNIT=CLHH;
PCLOP:UNIT=CLOM;