smdr sheet needed 1

[loff68]

to all that can help.......

Does anyone have a SMDR cheat sheet for the NEAX 2000IVS/IPS series systems?

 

[supertech2000]

What do you mean by cheat sheet? Do you want step by step on how to program smdr?? Are you connecting to the CPU or a PN-APOO?? Or do you want RS-232 pinouts for cables??

 

[mextera]

Try this,

1.) CM 05, Y= 0 > Sense Wheel setting number > 04
2.) Put AP00-B in Off-line mode. SW1 positions 1 & 4 ON, 2 & 3 OFF.
3.) CM D101 > 0000 > CCC
4.) Put AP00-B in On-line mode. SW1 all positions ON.
5.) Reset MP
6.) CM D001 > 20 > 5 (9600 baud)
7.) CM D001 > 21 > 0 (1 stop bit)
8.) CM D001 > 22 > 1 (8 data bits)
9.) CM D001 > 23 > 0 (no parity)
10.) CM D001 > 80 > 4 (SMDR)
11.) CM D001 > 81 > 0 (1st priority)
12.) CM D001 > 82 > 3 (2400 format)
13.) CM D001 > 83 > 0 (N/A)
14.) CM D001 > 84 > 1 (free wheel)
15.) CM D001 > 85 > 48 (SA)
16.) CM D001 > 86 > 33 (UA)
17.) CM D003 > 29 > 1~1000 for no memory card, 1~27000 with memory card
18.) Put AP00-B in Off-line mode. SW1 positions 1 & 4 ON, 2 & 3 OFF.
19.) CM D102 > 0000 > CCC
20.) Put AP00-B in On-line mode (SW1 all positions ON) and initialize AP00-B
21.) CM D016 > XX16 > 1 (outgoing SMDR for C.O. lines)
22.) CM D016 > XX21 > 1 (outgoing SMDR for Tie Lines)
23.) CM D016 > XX30 > 1 (incoming SMDR for C.O./Tie Lines if required)
24.) CM D027 > 0000~0009 > 9 (send to SMDR)
25.) CM D034 > 0000~0009 > 11 (local call)
26.) CM D000 > 70 > 1 (incoming SMDR if required)
27.) CM D000 > 77 > 1 (tandem SMDR if required)
28.) CM D000 > 79 > 1 (incoming & outgoing record on tandem SMDR if required)
29.) CM D000 > 238 > 1 (allow display of year)
30.) CM 13, YY=05 > Sta. No. > 0 (incoming SMDR by station if required)
31.) CM 13, YY=06 > Sta. No. > 1 (outgoing SMDR by station if required)
32.) CM 35, YY=14 > Rt. No. > 1 (outgoing SMDR by trunk route if required)
33.) CM 35, YY=49 > Rt. No. > 0 (incoming SMDR by trunk route if required)
34.) CM 08 > 040 > 0 (tandem SMDR if required)

If CCIS Centralized Billing feature is to be utilized the following is also required.

35.) CM 08 > 368 > 0 (Center office only. Set to a 1 in Remote office)
36.) CM 08 > 378 > 0 (Remote office only. Set to a 1 in Center office)
37.) CM 08 > 800 > 0 (Remote office only without AP00. Set to a 1 in Center office)
38.) CM A703 > CCH# > 1 (Center office only)
39.) CM A703 > CCH# > 0 (Remote office only)
40.) CM A704 > CCH# > Point Code of Centralized Billing Office (Remote site only)
41.) CM A704 > CCH# > NONE (Center office only)
42.) CM D000 > 76 > 1 (Center and Remote office)
43.) CM D001 > 179 > 1 (Center office only. Set to a 0 in Remote office)
44.) CM D001 > 239 > 1 (Center office only. Set to a 0 in Remote office)
45.) CM D016 > XX31 > 1 (Center and Remote office)
46.) CM D016 > XX32 > 1 (Center and Remote office)
47.) CM D016 > XX58 > 1 (Center and Remote office)

When using CCIS Centralized Billing the D003 command must be changed

48.) CM D003 > 26 > 1600 (Center and Remote office)
49.) CM D003 > 29 > 800 (Center and Remote office) NOTE



NOTE: The combined amount of call record numbers set in D003, 1st data, 23, 24, 26, 29, 30 must not exceed the following number.

No EXPMEM on AP00 is Provided EXPMEM on AP00 is Provided

When CMD001>179>0
(Not a center office for 1600 27000 Centralized Billing CCIS)

When CMD001>179>1
(Center office for Centralized 800 26000 Billing CCIS)

Mextera

 

[mextera]

Sorry this is to set SMDR to RS Port 0 On the AP00B .

Mextera

 

[loff68]

thank you....