RedTech443
MIS
I am setting up a remote site with a SLS configuration that has a newly installed PRI. I am not finding much information on a PRI sls configuration on a g430 gateway, I have found plenty on CO trunks however. Can anyone give this a once over and compare to their notes and see what I might be missing. I want to make sure this is going to work before I call police dispatch and do some testing.
One of my questions is, in a CO trunk you have to add the station that is allowed to call out, I am not so sure in a PRI trunk.
! version 36.9.0
Config info release 36.9.0 time "08:12:10 22 JAN 2015 " serial_number 14TG34697869
!
encrypted-username xxxxxxxxxxxxxxxxxxxxxxxx== password xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
hostname "DKHFAC01"
set system location "Remote Site"
set system name "WIC"
set system contact "IT"
no ip telnet
set port classification 10/3 regular
set port classification 10/4 regular
!
interface Vlan 1
icc-vlan
ip address 10.30.14.10 255.255.255.0
pmi
exit
!
interface FastEthernet 10/2
exit
!
interface USB-Modem
description "Default Modem Setup"
timeout absolute 10
ppp authentication ras
no shutdown
ip address 10.3.248.253 255.255.255.252
exit
!
set logging file enable
set logging file condition all Error
set logging file condition BOOT Debug
!
no snmp-server community
!
ip default-gateway 10.30.14.1 1 low
!
set mgc list 10.40.0.10
set mediaserver 10.40.0.10 10.40.0.10 23 telnet
set mediaserver 10.40.0.10 10.40.0.10 5023 sat
rtp-stat qos-trap
no rtp-stat fault
sls
set pim-lockout yes
set date-format dd/mm/yy
exit
!
sls
set slot-config v2 mm710
exit
!
sls
ds1 v2
exit
!
exit
!
sls
sig-group 4
set trunk-group-chan-select 4
set primary-dchannel 100v224
exit
!
exit
!
sls
station 7100 ip
set cor unrestricted
set encrypted-password "8ySyd/rz7rJv41SiS5LIPw=="
set name "WIC Front desk"
exit
!
exit
!
sls
trunk-group 4 t1-isdn
set tac #4
add port v201 4
add port v202 4
add port v203 4
add port v204 4
add port v205 4
add port v206 4
add port v207 4
add port v208 4
add port v209 4
add port v210 4
add port v211 4
add port v212 4
add port v213 4
add port v214 4
add port v215 4
add port v216 4
add port v217 4
add port v218 4
add port v219 4
add port v220 4
add port v221 4
add port v222 4
add port v223 4
set send-name no
set send-number no
exit
!
exit
!
sls
dial-pattern 1
set max-length 11
set min-length 11
set tgnum 4
set type fnpa
exit
!
dial-pattern 8
set max-length 7
set min-length 7
set tgnum 4
exit
!
dial-pattern 860
set max-length 10
set min-length 10
set tgnum 4
exit
!
dial-pattern 911
set tgnum 4
exit
!
exit
!
sls
set fac hold *30
set fac ars2 8
set fac ars1 9
exit
!
set sls enable
analog-test
exit
!#
!# End of configuration file. Press Enter to continue.
One of my questions is, in a CO trunk you have to add the station that is allowed to call out, I am not so sure in a PRI trunk.
! version 36.9.0
Config info release 36.9.0 time "08:12:10 22 JAN 2015 " serial_number 14TG34697869
!
encrypted-username xxxxxxxxxxxxxxxxxxxxxxxx== password xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
hostname "DKHFAC01"
set system location "Remote Site"
set system name "WIC"
set system contact "IT"
no ip telnet
set port classification 10/3 regular
set port classification 10/4 regular
!
interface Vlan 1
icc-vlan
ip address 10.30.14.10 255.255.255.0
pmi
exit
!
interface FastEthernet 10/2
exit
!
interface USB-Modem
description "Default Modem Setup"
timeout absolute 10
ppp authentication ras
no shutdown
ip address 10.3.248.253 255.255.255.252
exit
!
set logging file enable
set logging file condition all Error
set logging file condition BOOT Debug
!
no snmp-server community
!
ip default-gateway 10.30.14.1 1 low
!
set mgc list 10.40.0.10
set mediaserver 10.40.0.10 10.40.0.10 23 telnet
set mediaserver 10.40.0.10 10.40.0.10 5023 sat
rtp-stat qos-trap
no rtp-stat fault
sls
set pim-lockout yes
set date-format dd/mm/yy
exit
!
sls
set slot-config v2 mm710
exit
!
sls
ds1 v2
exit
!
exit
!
sls
sig-group 4
set trunk-group-chan-select 4
set primary-dchannel 100v224
exit
!
exit
!
sls
station 7100 ip
set cor unrestricted
set encrypted-password "8ySyd/rz7rJv41SiS5LIPw=="
set name "WIC Front desk"
exit
!
exit
!
sls
trunk-group 4 t1-isdn
set tac #4
add port v201 4
add port v202 4
add port v203 4
add port v204 4
add port v205 4
add port v206 4
add port v207 4
add port v208 4
add port v209 4
add port v210 4
add port v211 4
add port v212 4
add port v213 4
add port v214 4
add port v215 4
add port v216 4
add port v217 4
add port v218 4
add port v219 4
add port v220 4
add port v221 4
add port v222 4
add port v223 4
set send-name no
set send-number no
exit
!
exit
!
sls
dial-pattern 1
set max-length 11
set min-length 11
set tgnum 4
set type fnpa
exit
!
dial-pattern 8
set max-length 7
set min-length 7
set tgnum 4
exit
!
dial-pattern 860
set max-length 10
set min-length 10
set tgnum 4
exit
!
dial-pattern 911
set tgnum 4
exit
!
exit
!
sls
set fac hold *30
set fac ars2 8
set fac ars1 9
exit
!
set sls enable
analog-test
exit
!#
!# End of configuration file. Press Enter to continue.