SL 2100 sip trunk problem

[makuka]

Hi guys, noob on nec here...
In this scenario there are 2 nec sl 2100 coneccted via lan and both have sip trunk license, but the extensions can't call from the sl 2100 a trhough the nec sl 2100 b, later i Will update with more info.
Becuase i don't know if i can check the trunk status, i tried to create one sip trunk but didnt work.
Thanks in advance and sorry for My rusty English

 

[daddybadger]

I connected SL1100 via SIP trunking, probably work for a 2100 - I have a document that you can follow its most likely f-route or something like that you're having issues with.

SL Networking

 

[OzzieGeorge]

Hang on here, the OP hasn't said there are Sip trunk connections between the two systems or any other connection for that matter (other than ethernet). Why is the OP just assuming the two systems can route between each other just because of an ethernet connection? How are the two systems actually connected from a voice point of view and has any Froute programming been done?

 

[makuka]

I connected SL1100 via SIP trunking, probably work for a 2100 - I have a document that you can follow its most likely f-route or something like that you're having issues with.

SL Networking

Thanks for the reply, the sip trunk was working and after a power cut, it began with the problem, on Main sl 2100 i have the operator, dialing 0, and also the extension numbering plan with 3xxx, in the other sl 2100 extensión numerbing plan on 4xxx and dialing 0 for operador, but when i dial On this second sl2100 3xxx or 0 i get the busy tone

 

[makuka]

Hang on here, the OP hasn't said there are Sip trunk connections between the two systems or any other connection for that matter (other than ethernet). Why is the OP just assuming the two systems can route between each other just because of an ethernet connection? How are the two systems actually connected from a voice point of view and has any Froute programming been done?

Thanks for the reply, I'm viewing the backup of both systems, on the main SL 2100
Looking via quick install
Quick Install/Trunks/SIP Trunks/Profile 1/Interconnect IP without registration/Interconnect Remote Destinations
Sys nº: 0001
System Interconnection: Enable
Ip Address: 192.168.5.100
Call Control Port: 1720
Dial Number: 4
Keep Alive Mode For SIP: Option Keep Alive Mode
Domain Name:
Host Name:
User ID: 100
Domain Assignment: IP Address
SIP Carrier Choice: Carrier B
Register Sub Mode: disabled

User ID is the same number of the op extension number (MLT Phone)


44-02 001
Dial 4 F-Route table

44-05-01 F-Route table
1 = with group 2 (line 4 trough 7 SIP Lines)

10-36-00
Enable , User ID 100, Auth ID and pass empty


On the Second 2100

Quick Install/Trunks/SIP Trunks/Profile/Interconnect IP without Registration/Interconnect Remote Destinations.
Sys nº: 0001
System Interconnection: Enable
Ip Address: 192.168.5.100
Call Control Port: 1720
Dial Number: 4
Keep Alive Mode For SIP: Option Keep Alive Mode
Domain Name:
Host Name:
User ID: 100
Domain Assignment: IP Address
SIP Carrier Choice: Carrier B
Register Sub Mode: disabled

On Repots- Feature activation
5001 IP Terminal
Qty: 1
Status: on
Expires: unlimited

5103 VoIP Channel
Qty: 0
Status: off
Expires: unlimited

5111 IP Terminal
Qty: 1
Status: on
Expires: unlimited

5201 Mobile Extension (the don't use that feature)
Qty: 4
Status: on
Expires: unlimited

 

[OzzieGeorge]

Well the first issue I see is that they both have the same IP address!

 

[makuka]

Well the first issue I see is that they both have the same IP address!

Looking at the config via PCPro
i see different ip address configured under Quick Install/Trunks/SIP Trunks/Profile/Interconnect IP without Registration/Interconnect Remote Destinations.
I will upload screenshots of that config

 

[OzzieGeorge]

Again in system 2, both systems are set to the same IP!