SIP trunks and Routes

[ahannigan]

Settig up a Nortel C-1000 with 3 sip trunks to three Microsoft Unified Messaging Servers.
Looking for info on how to configure a route for multiple sip trunks, how to configre a single route (e.g. pilot number) for multiple sip trunks... and have the call set for ascending, descending, or cyclical.
With a standard pri i would just add all trunk members to group but not sure how to do this on c-1000 and sip.
Any info or docs would be great!!
thanks so much

 

[911guru]

You build a RDB like you would normally and then assign trunks to them as you would normally. There are some specific settings in the RDB for SIP / H.323. Here is an exampel of my SIP RDB:

CUST 0
ROUT 101

TYPE RDB  
CUST 00 
ROUT 101 
DES  SIP
TKTP TIE 
M911P NO 
ESN  NO  
RPA  NO  
CNVT NO  
SAT  NO  
RCLS INT 
VTRK YES 
ZONE 002 
PCID SIP 
CRID NO  
NODE 2000
DTRK NO  
ISDN YES 
    MODE ISLD
    DCH  100 
    IFC  SL1 
    PNI  00001 
    NCNA YES 
    NCRD YES 
    TRO  YES 
    FALT NO  
    CTYP UKWN
    INAC YES 
    ISAR NO  
    DAPC NO  
PTYP ATT 
AUTO NO  
DNIS NO  
DCDR YES 
ICOG IAO 
SRCH LIN 
TRMB YES 
STEP 
ACOD 2900101
TCPP NO  
TARG 01 
CLEN 10 
BILN NO
OABS 
INST 
ANTK 
SIGO STD 
STYP SDAT 
MFC  NO
ICIS YES
OGIS YES
PTUT 0 
TIMR ICF  512 
     OGF  512 
     EOD  13952 
     DSI  34944 
     NRD  10112 
     DDL  70 
     ODT  4096 
     RGV  640 
     GTO  896 
     GTI  896 
     SFB  3 
     NBS  2048 
     NBL  4096 
     IENB  5 
     TFD  0 
     VSS  0 
     VGD  6 
     EESD  1024 
SST  5 0 
DTD  NO  
SCDT NO  
2 DT NO  
NEDC ORG 
FEDC ORG 
CPDC NO  
DLTN NO  
HOLD 02 02 40 
SEIZ 02 02 
SVFL 02 02 
DRNG NO  
CDR  YES 
INC  YES 
LAST YES 
QREC NO  
OAL  YES 
AIA  NO  
OAN  YES 
OPD  NO  
NDP  EXC 0 
CDRX NO  
NATL YES 
SSL  
CFWR NO  
IDOP NO  
VRAT NO  
MUS  NO  
PANS YES 
MANO NO  
FRL  0 0 
FRL  1 0 
FRL  2 0 
FRL  3 0 
FRL  4 0 
FRL  5 0 
FRL  6 0 
FRL  7 0 
OHQ  NO  
OHQT 00 
CBQ  NO  
AUTH NO  
TDET NO  
TTBL 0 
ATAN NO  
OHTD NO  
PLEV 2 
OPR  NO  
ALRM NO  
ART  0 
PECL NO  
DCTI 0 
TIDY 2900101 101
ATRR NO  
TRRL NO  
SGRP 0 
CCBA NO  
ARDN NO  
AACR NO

And a trunk:

DES  SIP
TN   100 0 01 04  VIRTUAL
TYPE IPTI
CDEN 8D
CUST 0 
XTRK VTRK
ZONE 002 
LDOP BOP 
TIMP 600 
BIMP 600 
AUTO_BIMP NO
NMUS NO
TRK  ANLG
NCOS 0 
RTMB 101 1 
CHID 101 
TGAR 1 
STRI/STRO IMM IMM 
SUPN YES 
AST  NO  
IAPG 0 
CLS  CTD DIP CND ECD WTA LPR APN THFD XREP SPCD MSBT 
     P10 NTC MID 
TKID 
AACR NO
DATE  5 DEC 2007

911Guru

http://pbx-e911.com

 

[ahannigan]

Excellent, thanks so much. Can you do this from Element Manager the same way?

 

[911guru]

I am a CLI guy at heart, but Element Manager is very easy for this set-up as well. There is a good document on Nortel.com that goes over this (CS 1000 to BCM, but the SIP programming is generic enough)

http://support.nortel.com/go/main.jsp?cscat=DOCDETAIL&DocumentOID=646716.000000&searched=integration

You may need a login to get the document though.

911Guru

http://pbx-e911.com