Simply PIX501 setup not working

[neutec]

Hello All,
Im setting up a PIX501 and its been awhile since Ive play with Cisco. I apparently have missed something and was wondoering if someone could look over the below config and point out where I went wrong. Thanks in advance for your help.

PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname pixfirewall
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 100 permit ip any any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside xxx.xxx.xxx.xxx 255.255.255.248
ip address inside 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group 100 in interface outside
route outside 0.0.0.0 0.0.0.0 108.83.32.102 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.10-192.168.1.41 inside
dhcpd dns 68.94.156.1 68.94.157.1
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
terminal width 80
Cryptochecksum:9859044fd9723646b435be5c883b124e
: end

 

[unclerico]

add global (outside) 1 xxx.xxx.xxx.xxx

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[bluewire]

Check this out :

http://www.techsoup.org/learningcenter/hardware/page4783.cfm

 

[UltraZero]

Sooo.


Are you not able to do anything??

I see an access list to permit ip
I don't see anything to allow ICMP to test for pings?? (Maybe this is only needed on a Pix 525 which is what I have.

Another thing is you might need to (after entering the global command above) clear all ports.

I fought this issue for weeks and I cleared the ports and it came up intantly. Of course, I still can't get IPv6 to work.

 

[bluewire]

I think pix 525 and 501 doesn't support ipv6.

 

[bluewire]

I am sure about the 501.The version it can take is 6.3(5).Which doesn't support ipv6.