several PRI issues all at once

[PHXAZ]

Hello all I'm in a bit of a pickle.
I just finished installing a new Pri on a legend 6.0
all worked fine until I tried to program a 16 T/R for faxes.
the card was on slot 6 and would not come up. so smart me I moved it to slot 4 that used to have an 8 line card. once I did that and a Board renum. it all went to hell.
now my lines are messed pt they used to be 829-851 for PRI
827 was paging and 828 was music.
I tried to reprogramm on the fly and was able to renumber my pri lines 821-843 but my b-channels I cannot enter 0801 and 0808 it keep beeping back at me.
I can make calls but cannot receive calls.
my voicemail is not responding. here is my programmingon the PRI
can you see anyhting I'm missing.
I was able to get into auxilary and remove 827- from paging and 828 from music.
can someone please assist i nedd ot get this back up and running fast.
Thank you


A Slot 8 Switch: 5ESS

A System: By line

A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 1 8 CallbyCall By Dial Plan

A Channel ID: 23 22 21 20 19 18 17 16 15 14
A 13 12 11 10 9 7 6 5 4 3
A 2

A Line PhoneNumber NumberToSend
A 821
A 822
A 823
A 824
A 825
A 826
A 827
A 828
A 829
A 830
A 831
A 832
A 833
A 834
A 835
A 836
A 837
A 838
A 839
A 840
A 841
A 842
A 843

A Network Selection Table

A Entry Number: 0 1 2 3
A Pattern to Match: 101**** 10***

A Special Service Table

A Entry Number: 0 1 2 3 4 5 6 7
A Pattern to Match: 011 010 01 00 0 1
A Operator: none OP OP OP/P OP none none none
A Type of Number: I I I N N N N N
A Digits to Delete: 0 0 0 0 0 0 0 0

A Call-By-Call Service Table

A Entry Number: 0 1 2 3 4
A Pattern 0: 0
A Pattern 1: 1
A PRI INFORMATION


A Pattern 2: 2
A Pattern 3: 3
A Pattern 4: 4
A Pattern 5: 5
A Pattern 6: 6
A Pattern 7: 7
A Pattern 8: 8
A Pattern 9: 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ: No Service No Service No Service No Service No Service
A DeleteDigits: 0 0 0 0 0

A Entry Number: 5 6 7 8 9
A Pattern 0: 00
A Pattern 1: 00
A Pattern 2: 00 00
A Pattern 3: 00 00
A Pattern 4: 00 00
A Pattern 5: 0 00
A Pattern 6: 00
A Pattern 7: 00 00
A Pattern 8: 00 00
A Pattern 9: 00 00
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ: No Service No Service No Service No Service No Service
A DeleteDigits: 0 0 0 0 0

A Dial Plan Routing Table

A Entry Number: 0 1 2 3
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 4 4 0 0
A Pattern to Match: 1575 1573 2225 9810
A Digits to Delete: 4 4 4 4
A Digits to Add: 113 107 100 7139

A Entry Number: 4 5 6 7
A NtwkServ: Any service Any service Any service Any service
A Expected Digits: 0 0 0 0
A Pattern to Match: 1215
A Digits to Delete: 4 0 0 0
A Digits to Add: 7138

A Entry Number: 8 9 10 11
A NtwkServ: Any service Any service
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:

A Entry Number: 12 13 14 15
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A PRI INFORMATION

"Friends,Romans,Countrymen lend me your ears I come to ask for help and to give it, lets not argue on who is best or worst lets just help each other

 

[merlinman]

I hope you made a back up of the system when it worked w/o the 016 module.

Hopefully you did. If that's the case then put the 016 back where it was for now and restore that back up.

THEN, shoot the trouble on the 016.

If you didn't make a back up, then it looks like you'd have to start by erasing the system and starting from there.

MODULES SHOULD NEVER NEVER NEVER BE MOVED AROUND w/o considering the overall impact on the system design.

If you change the SYSTEM NUMBER of a PHYSICAL PORT that has other similar types of ports to its RIGHT, you usually fowl up everything in regards to those ports to the right.

http://home.comcast.net/~merlinman

-merlinmansblog.blogspot.com

 

[PHXAZ]

I got the voicemail up now i just nned to fix the incoming issue.
does anyone know what i'm missing om my programming or why i can't enter bchannel 0801 and 0808

"Friends,Romans,Countrymen lend me your ears I come to ask for help and to give it, lets not argue on who is best or worst lets just help each other

 

[Telecomboy]

If a line is in-use you cannot add it. If that is not the case and you know it is not in use, check the other b channel groups to make sure it is not assigned there.