Setting up serial voice mail integration 1

[3000gt]

Hi, we are trying to set up a serial port on the NIU board that will pass call information via rs-232 connection to a VM system.

We have created analog extension, that are part of a hunt group. However, we cannot set up the ICU connection correctly.

Here is a log of commands attempted to set this up:

the only ICFUC(change IFC) command it accepted:

<ICFUC:MWF=ALL,IFCIND=1,DFMT=3,UPDFCN=YES,FILLER=48;


ICF printout command:

ICFUP:IFCIND=1;

ICFUP;

INFORMATION COMPUTER COMMON FUNCTIONS DATA
UPDATING START TIME IS NOT VALID
MESSAGE WAITING FUNCTIONALITY IS ALL
INFORMATION COMPUTER EQUIPMENT DATA
IFCIND IODEV EQU RATE DFMT UPDFCN PARITY CCHECK
1 SYSNET 3 YES
FILLER=48 ICEXG=NONE USER=GICI-01

ICFUI:IFCIND=2,DFMT=3,EQU=1-0-60-2,RATE=2400,UPDFCN=YES,PARITY=NONE,CCHECK=YES,TXC=YES,FILLER=48;
NOT ACCEPTED
INCORRECT BOARDTYPE

ICFUI:IFCIND=2,EQU=001-0-60-2,RATE=2400,PARITY=NONE,TXC=YES,CCHECK=YES,DFMT=3,UPDFCN=NO;
NOT ACCEPTED
EQUIPMENT POSITION ALREADY ASSIGNED

iNPUT/OUTPUT DEVICE PORT SETUP

Ioddp: I/O DEVICE DATA

IODDP;
I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU SIPOS TYPE/USAGE STATUS AUTH
SYSN - 001-0-60 - - IN SERVICE
SYSN SYSDISK1 001-0-60-0 3 ADTX IN SERVICE
SYSSUBFS11
SYSSUBFS21
SYSN SYSTERMINAL 001-0-60-1 - MML - 7
SYSN MCI 001-0-60-2 - NETWORK/OUT IN SERVICE
SYSN SYSNET 001-0-60-4 - NETWORK/OUT IN SERVICE
SYSN TCP-IP2 001-0-60-4 - NETWORK/MML - 7
SYSN TCP-IP3 001-0-60-4 - NETWORK/MML - 7
SYSN TCP-IP4 001-0-60-4 - NETWORK/MML - 7

I/O DEVICE INITIATE:

IOIFC:IODEV=MCI,IFACE=V24,BAUDR=2400,WORDL=8,PARITY=NONE,STPBIT=1,PROC=ECHO;

CHANGE:

IOIFC:IODEV=SYSTERMINAL,IFACE=V24,BAUDR=2400,WORDL=8,PARITY=NONE,STPBIT=1,PROC=ECHO;


vm

VMPOP;
VOICE MAIL PORT DATA
DIR PORT IFCIND
2001 01 1
2002 02 1
2003 03 1
2004 04 1



Expertise in Avaya, Rolm/Siemens, Mitel, Nortel, NEC, Alcatel, Toshiba, Aspect, Ericsson, Executone, Panasonic PBXs & KSUs

 

[doktor]

Hi 3000gt

I just described this in another thread:

You are trying to set-up a NIU board with ICU2 board commands.

I have written the correct commands for MD110 and VM for NIU.

In this example, commands are for MD110 BC11:

Initiate the wanted number of analogue extensions:
EXTEIIR=,EQU=,TYPE=EL6,TRAF=03141401,SERV=000010000,TRM=3,
CDIV=000151000,ROC=000001;
Change these extensions to global tones for the VMX-100:
EXCACIR=,ICAT=0010;
Initiate the Voice Mail group:
GHGRI:GRP=,LIM=,SERV=1000,TRAF=15,SEL=11000,QUE=00;
GHGMI:GRP=,DIR=;
Initiate the NIU board:
CNHUI:BPOS=x-x-xx;
IOBPI:NODE=NIU,BPOS=;
Initiate an EQU for Voice Mail V24 on the NIU board:
IOEQI:EQU=X-X-XX-X,IODEV=VMGICI9,USAGE=OUT;
Change Baud rate, Parity, Word-length, stop bits with:
IOIFC:IODEV=VMGICI9,BAUDR=2400,WORDL=7,STPBIT=1,PARITY=EVEN;
Check with: IOIFP;
Initiate the data channel on the NIU board:
ICFUI:IFCIND=5,DFMT=5,UPDFCN=NO,FILLER=32,IODEV=VM-GICI9;
ICFUC:MWF=ALL;
Set the SID (System ID)
ICMWC:SID=5,KFCN=MWC,DIG=group number,DTXT=group number;
Check with:
ICFUP:IFCIND=5;
ICMWP:SID=5;
Initiate the Voice Mail function:
VMFUI:IFCIND=5,VMF=EXTN2,POFMT=2;
Initiate the voice mail function on each analogue extension:
VMPOIIR="first group member",PORT=11,IFCIND=5;
VMPOIIR="second group member",PORT=12,IFCIND=5;
VMPOIIR="third group member",PORT=13,IFCIND=5;
VMPOIIR="fourth group member",PORT=14,IFCIND=5;

VMPOI:GRP=group number,IFCIND=5;

The VMPOP result will then be:
<VMPOP;
VOICE MAIL PORT DATA
DIR PORT IFCIND
10001 11 5
10002 12 5
10003 13 5
10004 14 5
VOICE MAIL GROUP DATA
GRP IFCIND
4000 5
END


Allmost same expertice here:
Expertise in Avaya, Rolm/Siemens, Mitel, Nortel, NEC, Alcatel, Toshiba, Aspect, Ericsson, Executone, Panasonic PBXs & KSUs

BUT for this case my knowledge of MD110 and Voice mail systems is sufficient.




Best regards doktor

 

[doktor]

Hi again

If you need the correct commands for the ICU2 board, please write here again.

doktor

 

[3000gt]

Thanks for the quick reply. Will try those commands and then test the serial port out. We are basically just trying to see the call information sent through the serial port of the NIU board on sw version BC11, by calling the hunt group pilot and watching it with Procomm.


We are learning the Ericsson PBX right now, we have worked with Ericsson on an in-skins wireless mobile business phone system project previously.

Expertise in Avaya, Rolm/Siemens, Mitel, Nortel, NEC, Alcatel, Toshiba, Aspect, Ericsson, Executone, Panasonic PBXs & KSUs

 

[doktor]

OK

Let me hear your comments on my command-list, when you have tried it out.
Thank you.

The doktor

 

[3000gt]

We were able to program all the commands up to this one:

Initiate the Voice Mail function:
VMFUI:IFCIND=5,VMF=EXTN2,POFMT=2;

This is what the PBX responded:

VMFUI:IFCIND=5,VMF=EXTN2,POFMT=2;
NOT ACCEPTED
LICENSE SERVER IS TEMPORARILY BLOCKED

Expertise in Avaya, Rolm/Siemens, Mitel, Nortel, NEC, Alcatel, Toshiba, Aspect, Ericsson, Executone, Panasonic PBXs & KSUs

 

[mundus]

Hi,
this is only a respons for:

NOT ACCEPTED
LICENSE SERVER IS TEMPORARILY BLOCKED

Read in the licens by LIDAIATH=....
and do a SFCEI

 

[3000gt]

Mundus, thanks for the info. Also, do you know where the license file (path) would be located, or where the default locations are? Is it stored on the PBX hard drive or on the maintenance PC?

Expertise in Avaya, Rolm/Siemens, Mitel, Nortel, NEC, Alcatel, Toshiba, Aspect, Ericsson, Executone, Panasonic PBXs & KSUs

 

[PetrNik]

Hello,
Make
FIDAPATH= /SYSN/USR1/SES/LI,OPT=ALL;
File with extension .LIC is license file.
Than make
LIDAIATH= /SYSN/USR1/SES/LI/thisfile.LIC;