I get these errors on the scsi drive which I do not know how to handle.
Would greatly appreciate any help.
Basically this scsi controlloer was conectd to an IBM 3581 autoloader (a 7 tape 1.4 TB backup library) connected from a linus redhat 7.1 witha 2.4.6 kernel. This happend while testing the backup system and I guess I wont be able to porceed further without taking carre of this.
Thanks
edit: /var/log/dmesg
scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
<Adaptec aic7880 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
Vendor: IBM Model: ULT3581-TA Rev: I105
Type: Medium Changer ANSI SCSI revision: 02
Vendor: IBM Model: ULT3580-TD1 Rev: 16E0
Type: Sequential-Access ANSI SCSI revision: 03
(scsi0:A:3): 80.000MB/s transfers (40.000MHz, offset 23, 16bit)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x148) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x2.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x3.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x77) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x2.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
Vendor: SEAGATE Model: ST39102LW Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
(scsi1:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
scsi1:0:0:0: Tagged Queuing enabled. Depth 253
Detected scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 17783240 512-byte hdwr sectors (9105 MB)
Partition check:
sda: sda1 sda2 < sda5 sda6 >
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
LVM version 0.9.1_beta2 by Heinz Mauelshagen (18/01/2001)
lvm -- Driver successfully initialized
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 200k freed
Adding Swap: 2096440k swap-space (priority -1)
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 15:14:49 Feb 7 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xdce0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
st: bufsize 32768, wrt 30720, max init. buffers 4, s/g segs 16.
Would greatly appreciate any help.
Basically this scsi controlloer was conectd to an IBM 3581 autoloader (a 7 tape 1.4 TB backup library) connected from a linus redhat 7.1 witha 2.4.6 kernel. This happend while testing the backup system and I guess I wont be able to porceed further without taking carre of this.
Thanks
edit: /var/log/dmesg
scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.1.13
<Adaptec aic7880 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/255 SCBs
Vendor: IBM Model: ULT3581-TA Rev: I105
Type: Medium Changer ANSI SCSI revision: 02
Vendor: IBM Model: ULT3580-TD1 Rev: 16E0
Type: Sequential-Access ANSI SCSI revision: 03
(scsi0:A:3): 80.000MB/s transfers (40.000MHz, offset 23, 16bit)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x148) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x2.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x3.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x77) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x1a3) SCSIRATE(0x93)
(scsi0:A:3:1): parity error detected in Data-in phase. SEQADDR(0x76) SCSIRATE(0x93)
(scsi0:A:3:1): data overrun detected in Data-in phase. Tag == 0x2.
(scsi0:A:3:1): Have seen Data Phase. Length = 256. NumSGs = 1.
sg[0] - Addr 0x37d6e040 : Length 32
Vendor: SEAGATE Model: ST39102LW Rev: 0004
Type: Direct-Access ANSI SCSI revision: 02
(scsi1:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
scsi1:0:0:0: Tagged Queuing enabled. Depth 253
Detected scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 17783240 512-byte hdwr sectors (9105 MB)
Partition check:
sda: sda1 sda2 < sda5 sda6 >
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
LVM version 0.9.1_beta2 by Heinz Mauelshagen (18/01/2001)
lvm -- Driver successfully initialized
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 200k freed
Adding Swap: 2096440k swap-space (priority -1)
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.259 $ time 15:14:49 Feb 7 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xdce0, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.251:USB Universal Host Controller Interface driver
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Detected scsi tape st0 at scsi0, channel 0, id 3, lun 0
st: bufsize 32768, wrt 30720, max init. buffers 4, s/g segs 16.