Routing question 1

[td1031]

I am having an issue dialing a specific NPA-NXX and I cant figure out where it is being blocked.

LD 90 print looks good for the NPA and I can call other NPA-NXX's in that area code.

NPA 1912
RLI 1
SDRR NONE
ITEI NONE

 

[td1031]

If I dial 1912267XXXX the call routes fine but 1912562XXXX I immediately get fast busy and release and try again message on the phone.

 

[td1031]

RLI 1
ENTR 0
LTER NO
ROUT 10
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 4
DMI 2
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ YES

ENTR 1
LTER NO
ROUT 1
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP YES
FRL 4
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ISET 2
NALT 5
MFRL 3
OVLL 0

TYPE TLST
TKTP TIE
ROUT 10
DES LD
TN 003 01 MBER 1 LD
TN 003 02 MBER 2 LD
TN 003 03 MBER 3 LD
TN 003 04 MBER 4 LD
TN 003 05 MBER 5 LD
TN 003 06 MBER 6 LD
TN 003 07 MBER 7 LD
TN 003 08 MBER 8 LD
TN 003 09 MBER 9 LD
TN 003 10 MBER 10 LD
TN 003 11 MBER 11 LD
TN 003 12 MBER 12 LD
TN 003 13 MBER 13 LD
TN 003 14 MBER 14 LD
TN 003 15 MBER 15 LD
TN 003 16 MBER 16 LD
TN 003 17 MBER 17 LD
TN 003 18 MBER 18 LD
TN 003 19 MBER 19 LD
TN 003 20 MBER 20 LD
TN 003 21 MBER 21 LD
TN 003 22 MBER 22 LD
TN 003 23 MBER 23 LD


Not sure what i am missing but this looks good RLI 1 point to route 10 which is my LD trunks

 

[hawks]

What does DMI 2 look like

 

[acewarlock]

More than likley your being blocked by the telco.

 

[brewerdude]

Dial the number using the ACOD of your trunk group on an unrestricted set (TGAR = 0 and UNR in class). To get the ACOD, print the RDB of your route 10.

If you can dial it using the ACOD then something is wrong in your BARS. If you can't dial it this way, then it's something with the telco. The other advantage to this method is that you may hear the telco error messages associated with the problem.

 

[Reusser]

you can also turn on your DCH messages. If you see an Outgoing setup message and an incoming reject, chances are telco blocking.

One thing you might check though is DSEL prompt in route. If call is to a 3.1k device and DSEL is VCE, call will be blocked.

Try changing DSEL to 3vce

 

[lamasu]

I would still check to see what DMI 2 is doing first.

Regards,
Lamasu

 

[johnpoole]

1912267XXXX the call routes fine but 1912562XXXX

that statement would remove the dmi issue in most switches.. i can;t add a dmi that blocks past the fourth digit..

NPA  1912
RLI  1 
SDRR NONE
ITEI NONE

with nothing added as an allow or deny, the block is from the provider.. when in doubt i dial the acod plus the number.

john poole
bellsouth business
columbia,sc