Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Westi on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Restore PRI Card
- Thread starter jsaad
- Start date
- Thread starter
- #3
VxWorks System Boot
Copyright 1984-1996 Wind River Systems, Inc.
CPU: MCXXXAA
Version: 5.3.1
BSP version: 3.0.1.7
Creation date: Dec 3 1999, 09:27:04
Press *any* key to stop this auto-boot...
0
auto-booting...
boot device : flash
unit number : 0
processor number : 0
file name : vxworks
inet on ethernet (e) : 192.168.1.1
flags (f) : 0x0
target name (tn) : pricard4512
other (o) : flash,c:/,xqt,sx2c-na.cmd
filename 'vxworks':
creating flash device
calling dosFsInit
mounting flash - Flash mounted on /flash/
cd'd to /flash/
Loading vxworks ...open succeeded, fd=4
1038596 + 109496 + 953248
Starting at 0x2001000...
Attached TCP/IP interface to qu unit 0
Attaching interface lo0...done
Adding 4702 symbols for standalone.
VxWorks
Copyright 1984-1998 Wind River Systems, Inc.
CPU: MCXXXAA
VxWorks: 5.4
BSP version: 4.2/2
Creation date: Mar 24 2005
WDB: Ready.
flash,c:/,xqt,sx2c-na.cmd
MBAR:f000000
SSDRV:c:/ mounted with options 0x0
Copyright (c) 1993-1996 Wind River Systems, Inc. All rights reserved
ver: 2.6 FCS
Disk Check In Progress ...
total disk space (bytes) : 7,225,344
bytes in each allocation unit : 2,048
total allocation units on disk : 3,528
bad allocation units : 0
available bytes on disk : 2,412,544
available clusters on disk : 1,178
maximum available contiguous chain (bytes) : 2,408,448
available space fragmentation (%) : 1
clusters allocated : 2,350
Done Checking Disk.
Change to FLASH DIR: c:/
Started ppp1 listener task, tid 0x2dd338c
listening for ppp
SSXSPART.c:Loading FPGA file: pri_fpga.bin
................
SSXSPART.c:Xilinx File Obtained, Sum 31216
NAME: fpga.ncd
PART: s30xlpq208
DATE: 1999/07/23
TIME: 09:51:54
SIZE: 31146 bytes.
Correct clock count = 249161.
Config data ends on bit 1
fpga download completed successfully.
SSXSPART.c:Xilinx Loaded OK
Card Type is MCXXXAA
Module Site 1 - No module present.
Module Site 2 - DualJET Module present.
Settings:
Trunk 0 impedance set for 120-ohms.
Trunk 1 impedance set for 120-ohms.
Module Site 3 - No module present.
SS: Starting POST FPGA...
SS: Starting POST DX...
SS: Starting POST LDX...
SS: Starting POST Framer...
Framer 0: MT9074 JET (T1)
Framer 1: MT9074 JET (T1)
SS: POST2 PASSED...
Programming the modules
Module Site 2 - DualJET Module present.
Settings:
Trunk 0 impedance set for 100-ohms.
Trunk 1 impedance set for 100-ohms.
Loading "nastack.o"
nastack.o loaded ok
Loading "hdlc_drv.o"
Unsupported Object module format, a_machtype : 0
ld error: error reading file (errno = 0x3d0001).
Load of `hdlc_drv.o' failed
Loading "pri_sx2c.o"
undefined symbol: _MiLAP_Receive_Queue
undefined symbol: _MiLAP_Transmit
ld error: error reading file (errno = 0x1c0001).
Load of `pri_sx2c.o' failed
SSAPP: Found Function _ngmain()
Spawning tNgMain 130 0 32000 0x2b00b6e
Spawned task id: 45090908
fdSlave2 = 13 f
dMaster2 = 14
| INFO GW | 70/01/01 00:00:00 | ---start------------------------
| INFO GW | 70/01/01 00:00:00 | ---start------------------------
Logfile scan stopped at pos
ition 195237 curr_stamp_num = 27109 stamp_num = 27109
| INFO GW | 70/01/01 00:00:00 | Dt: PRICARD 24-MAR-2005 [VER-8.2.1.5] [ngstar
t.cpp @ 159] | 1234
SS: SS_StartupTask Complete!
| WARN GW | 70/01/01 00:00:06 | no TRL and TRA information in database (no Mi
n/Max limiting being done) [rtmmasn.cpp @ 407] | 1234
| INFO GW | 70/01/01 00:00:06 | Min/Max database loaded [rtmmbld.cpp @ 1303]
| 1234
| INFO GW | 70/01/01 00:00:06 | PRA drivers started successfully! [pradvr.cpp
@ 486] | 1234
SSAPP: Can't Locate Function _hdlc_init()
| WARN GW | 70/01/01 00:00:06 | dumping memory for upcoming fatal [oserror.cp
p @ 119] | 1234
| FATAL GW | 70/01/01 00:00:06 | Unknown entry point _hdlc_init
[stack.cpp @ 137] | 1234
start: 70/01/01 00:00:06 end: 70/01/01 00:00:06
| HALT GW | 70/01/01 00:00:06 | start: 70/01/01 00:00:06 end: 70/01/01 00:0
0:06 | 1234
| WARN GW | 70/01/01 00:00:06 | SUICIDE: from stack.cpp:137 [hardware.cpp @ 2
18] | 1234
| HALT GW | 70/01/01 00:00:07 | ISDN Application has TERMINATED [stack.cpp @
137] |
Copyright 1984-1996 Wind River Systems, Inc.
CPU: MCXXXAA
Version: 5.3.1
BSP version: 3.0.1.7
Creation date: Dec 3 1999, 09:27:04
Press *any* key to stop this auto-boot...
0
auto-booting...
boot device : flash
unit number : 0
processor number : 0
file name : vxworks
inet on ethernet (e) : 192.168.1.1
flags (f) : 0x0
target name (tn) : pricard4512
other (o) : flash,c:/,xqt,sx2c-na.cmd
filename 'vxworks':
creating flash device
calling dosFsInit
mounting flash - Flash mounted on /flash/
cd'd to /flash/
Loading vxworks ...open succeeded, fd=4
1038596 + 109496 + 953248
Starting at 0x2001000...
Attached TCP/IP interface to qu unit 0
Attaching interface lo0...done
Adding 4702 symbols for standalone.
VxWorks
Copyright 1984-1998 Wind River Systems, Inc.
CPU: MCXXXAA
VxWorks: 5.4
BSP version: 4.2/2
Creation date: Mar 24 2005
WDB: Ready.
flash,c:/,xqt,sx2c-na.cmd
MBAR:f000000
SSDRV:c:/ mounted with options 0x0
Copyright (c) 1993-1996 Wind River Systems, Inc. All rights reserved
ver: 2.6 FCS
Disk Check In Progress ...
total disk space (bytes) : 7,225,344
bytes in each allocation unit : 2,048
total allocation units on disk : 3,528
bad allocation units : 0
available bytes on disk : 2,412,544
available clusters on disk : 1,178
maximum available contiguous chain (bytes) : 2,408,448
available space fragmentation (%) : 1
clusters allocated : 2,350
Done Checking Disk.
Change to FLASH DIR: c:/
Started ppp1 listener task, tid 0x2dd338c
listening for ppp
SSXSPART.c:Loading FPGA file: pri_fpga.bin
................
SSXSPART.c:Xilinx File Obtained, Sum 31216
NAME: fpga.ncd
PART: s30xlpq208
DATE: 1999/07/23
TIME: 09:51:54
SIZE: 31146 bytes.
Correct clock count = 249161.
Config data ends on bit 1
fpga download completed successfully.
SSXSPART.c:Xilinx Loaded OK
Card Type is MCXXXAA
Module Site 1 - No module present.
Module Site 2 - DualJET Module present.
Settings:
Trunk 0 impedance set for 120-ohms.
Trunk 1 impedance set for 120-ohms.
Module Site 3 - No module present.
SS: Starting POST FPGA...
SS: Starting POST DX...
SS: Starting POST LDX...
SS: Starting POST Framer...
Framer 0: MT9074 JET (T1)
Framer 1: MT9074 JET (T1)
SS: POST2 PASSED...
Programming the modules
Module Site 2 - DualJET Module present.
Settings:
Trunk 0 impedance set for 100-ohms.
Trunk 1 impedance set for 100-ohms.
Loading "nastack.o"
nastack.o loaded ok
Loading "hdlc_drv.o"
Unsupported Object module format, a_machtype : 0
ld error: error reading file (errno = 0x3d0001).
Load of `hdlc_drv.o' failed
Loading "pri_sx2c.o"
undefined symbol: _MiLAP_Receive_Queue
undefined symbol: _MiLAP_Transmit
ld error: error reading file (errno = 0x1c0001).
Load of `pri_sx2c.o' failed
SSAPP: Found Function _ngmain()
Spawning tNgMain 130 0 32000 0x2b00b6e
Spawned task id: 45090908
fdSlave2 = 13 f
dMaster2 = 14
| INFO GW | 70/01/01 00:00:00 | ---start------------------------
| INFO GW | 70/01/01 00:00:00 | ---start------------------------
Logfile scan stopped at pos
ition 195237 curr_stamp_num = 27109 stamp_num = 27109
| INFO GW | 70/01/01 00:00:00 | Dt: PRICARD 24-MAR-2005 [VER-8.2.1.5] [ngstar
t.cpp @ 159] | 1234
SS: SS_StartupTask Complete!
| WARN GW | 70/01/01 00:00:06 | no TRL and TRA information in database (no Mi
n/Max limiting being done) [rtmmasn.cpp @ 407] | 1234
| INFO GW | 70/01/01 00:00:06 | Min/Max database loaded [rtmmbld.cpp @ 1303]
| 1234
| INFO GW | 70/01/01 00:00:06 | PRA drivers started successfully! [pradvr.cpp
@ 486] | 1234
SSAPP: Can't Locate Function _hdlc_init()
| WARN GW | 70/01/01 00:00:06 | dumping memory for upcoming fatal [oserror.cp
p @ 119] | 1234
| FATAL GW | 70/01/01 00:00:06 | Unknown entry point _hdlc_init
[stack.cpp @ 137] | 1234
start: 70/01/01 00:00:06 end: 70/01/01 00:00:06
| HALT GW | 70/01/01 00:00:06 | start: 70/01/01 00:00:06 end: 70/01/01 00:0
0:06 | 1234
| WARN GW | 70/01/01 00:00:06 | SUICIDE: from stack.cpp:137 [hardware.cpp @ 2
18] | 1234
| HALT GW | 70/01/01 00:00:07 | ISDN Application has TERMINATED [stack.cpp @
137] |
- Status