Resetting problems

[korexxkun]

I wish to reset my nortel pbx password from my flash card. This is what i kept getting.



<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen

General Software Pentium M Embedded BIOS(R) 2000 Revision 5.3
Copyright (C) 2005 General Software, Inc. All rights reserved.
Nortel Call Processor - Pentium M


00000589K Low Memory Passed
02083712K Ext Memory Passed
Wait.....

PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 3580 Host Bridge
00 00 01 8086 3584 System
00 00 03 8086 3585 System
00 01 00 8086 3581 PCI-to-PCI Bridge
00 02 00 8086 3582 VGA Display 12
00 1D 00 8086 24C2 Serial Bus 12
00 1D 01 8086 24C4 Serial Bus 11
00 1D 07 8086 24CD Serial Bus 10
00 1E 00 8086 244E PCI-to-PCI Bridge
00 1F 00 8086 24C0 ISA Bridge
00 1F 01 8086 24CB IDE Controller 9
00 1F 03 8086 24C3 Serial Bus 7
02 00 00 104C AC56 CardBus Bridge 11
02 01 00 8086 1209 Ethernet 12
02 02 00 8086 1209 Ethernet 7
02 03 00 8086 1078 Ethernet 9
Plug-n-Play v1.0A Copyright (C) 2005 General Software, Inc.

Polling Hard Drive and Compact Flash Locations


+------------------------------------------------------------------------------+
| System BIOS Configuration, (C) 2005 General Software, Inc. |
+---------------------------------------+--------------------------------------+
| System CPU : Pentium M | Low Memory : 632KB |
| Coprocessor : Enabled | Extended Memory : 2035MB |
| Ide 0 Type : 3 | Serial Ports 1-2 : 03F8 02F8 |
| Ide 1 Type : 3 | ROM Shadowing : Enabled |
| Ide 2 Type : 3 | BIOS Version : NTDU74AA 18 |
+---------------------------------------+--------------------------------------+

Press F to force board to boot from faceplate drive.
.........


CPU Frequency = 1400 MHz

Attempting to boot from faceplate drive.


SYSLINUX 3.63 2008-04-10 EBIOS Copyright (C) 1994-2008 H. Peter Anvin

SYSLINUX 3.63 2008-04-10 Copyright (C) 1994-2008 H. Peter Anvin





Welcome to the CS 1000 Linux Base System Installer

- To install via a serial console on COM1, type com1 <ENTER>.
All input and output will be directed to the COM1 serial port. The system
console will be permanently installed on COM1.

***The default is --- com1***.

boot: recovery-com1
Loading vmlinuz...............................
Loading initrd.img..............................................................
........................................................ready.










G######################################################################A(100)ass
Welcome to Red Hat Enterprise Linux Server
+--------------------+ Select Partition +---------------------+
| |
| What partition and directory on that partition hold the |
| CD (iso9660) images for Red Hat Enterprise Linux Server? |
| If you don't see the disk drive you're using listed here, |
| press F2 to configure additional devices. |
| |
| /dev/hda1 ^ |
| /dev/hda10 # |
| /dev/hda11 : |
| /dev/hda2 : |
| /dev/hda3 v |
| |
| Directory holding images: /___________________________ |
| |
| +----+ +------+ |
| | OK | | Back | |
| +----+ +------+ |
| |
| |
+-------------------------------------------------------------+

<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen




It doesnt bring up the recovery console with password reset options. what do i do?