Replacing 408 GS/LS with 408 GS/LS/MLX?

[wswhite]

I want to remove a 408 GS/LS card in slot 2 and replace it with a 408 GS/LS-MLX. When I do this and immediately place a long distance call it goes through. Now if I do a board renumber to account for the 408 GS/LS-MLX I loose my long distance capability. Some how switching these two boards is affecting my T1 configuration. Any ideas? Here is the configuration:

Slot 0 CKE4 CPU
Slot 1 008 MLX
Slot 2 408 GS/LS
Slot 3 400 GL/LS/TTR
Slot 4 100D
Slot 5 012
Slot 6 012
Slot 7 012
Slot 8 408 GS/LS-MLX
Slot 9 008 MLX-U
Slot 10 800 NI-BRI
Slot 11 012

Thanks in advance.

 

[gregarican]

After the board renumber have you gone in and done a System Printout? Information from this should point you in the exact direction. Let me know what this card looks like as reflected in the System Printout.

 

[gregarican]

One tip to narrow things down is when you perform a board renumber the Logical ID's that get assigned to trunks and extensions can be automatically modified to account for new items. Perhaps these Logical ID's have affected your trunking for outside facilities.

If you have a saved copy of a previous System Printout you could compare it when the current System Printout to verify if this is indeed the case.

 

[wswhite]

Here is the System Setup printout:

A SYSTEM INFORMATION


A Current Date: 07/22/02
A Current Time: 17:30:13

A System : Mode AutoMaintBusy AutoBusyTie
A : Hybrid/PBX Disable Disable

A Language: SystemLang SMDR Printer
A English English English

A CTI Links :
A Direct Line Operators : 100
A Queued Call Operators :
A SysProg Port : 100 Password : craftr4

A Transfer : Type Audible OneTouch(Complete) ReturnTimer
A : Ring MusicOnHold Transfer(Manual) 4 rings

A VMS Transfer Return Interval : 9
A Paging System Lines :
A Music On Hold Line : 808
A Camp On Time : 90 sec
A Call Park Return Time : 180 sec
A Auto Callback Rings : 3
A Extension Status (ESS) : Group Call / CMS
A ESS Operators : 100

A SMDR: Min.CallTime CallReport Format TalkTime UDP
A : 101 sec In/Out ISDN Enable In/Out

A Intercom Dial Tone : Inside
A Reminder Service Cancel : :

A Behind Switch Code : Drop Transfer Conference
A :

A Inter-digit Timers (seconds) : 5 24 24 24 10 10 10 5 5
A Recall Timer : 450 msec
A Second Dial-tone Timer : 0 msec
A Rotary Line Cut Through : Delay
A Unassigned Extension : 100

A Automatic Backup : Daily - 04:00

A T1/PRI/BRI Clock Synchronization:
A Primary Secondary Tertiary
A 4/1 Loop

A Slot # 0: CKE4 CPU
A Slot # 1: 008 MLX
A Slot # 2: 408 GS/LS
A Slot # 3: 400 GS/LS/TTR
A Slot # 4: 100D
A Slot # 5: 012
A Slot # 6: 012
A Slot # 7: 012
A Slot # 8: 408 GS/LS-MLX
A Slot # 9: 008 MLX-U
A Slot # 10: 800 NI-BRI
A Slot # 11: 012
A Slot # 12: Not Used
A Slot # 13: Not Used
A Slot # 14: Not Used
A Slot # 15: Not Used
A Slot # 16: Not Used
A Slot # 17: Not Used

 

[gregarican]

What I was looking for is further down. The line/trunk information will show Logical ID's, Line #'s, Pool #'s, etc. If you have a previously saved report (before you performed the board renumber) you probably would notice that some of the trunks/lines are assigned differently.