Remove Magazine in BC9 System

[MirkoGradassi]

I need to remove a magazine froma BC9 System with 2 magazines. I've shut down everything, than Disconnnect the DSU and power from second magazine. I've cnboe all of the board in mag 1 and temove the reu. Then I've switch on magazine one, block the lim with the command
BLLTI:LIM=1;

and refresh the hardware with command:
SFCEI;

Afret all I unblock the LIM with BLLTE:LIM=1;

Now, the CNLIP:LIM=1,DEV=YES; command report this output:

****************************************************
<CNLIP:LIM=1,DEV=YES;

LIM CONFIGURATION

LIM NUMBER 1
LIM CONTROL LIM CONTROL NUMBER OF SERVICE
SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM
A EXECUTING 0 ACTIVE
B NOT EQUIPPED
MEMORY MEMORY MEMORY SPARE
VOLUME SPARE AFTER PACKING
24575 KB 6406 KB 6406 KB

BUAR1 1422 KB BUAR2 INVALID

DEVICE BOARDS
NUMBER OF
BPOS BOARDID INDIVIDUALS SERVICE STATE
001-0-00 NOT EQUIPPED
001-0-01 NOT EQUIPPED
001-0-02 NOT EQUIPPED
001-0-03 NOT EQUIPPED
001-0-10 NOT EQUIPPED
001-0-11 NOT EQUIPPED
001-0-12 NOT EQUIPPED
001-0-13 NOT EQUIPPED
001-0-20 69 4 ACTIVE
001-0-21 NOT EQUIPPED
001-0-22 NOT EQUIPPED
001-0-23 NOT EQUIPPED
001-0-30 NOT EQUIPPED
001-0-31 NOT EQUIPPED
001-0-32 NOT EQUIPPED
001-0-33 NOT EQUIPPED
001-0-40 NOT EQUIPPED
001-0-41 NOT EQUIPPED
001-0-42 NOT EQUIPPED
001-0-43 NOT EQUIPPED
001-0-50 NOT EQUIPPED
001-0-51 NOT EQUIPPED
001-0-52 NOT EQUIPPED
001-0-53 NOT EQUIPPED
001-0-60 NOT EQUIPPED
001-0-61 NOT EQUIPPED
001-0-62 NOT EQUIPPED
001-0-63 NOT EQUIPPED
001-0-70 NOT EQUIPPED
001-0-71 NOT EQUIPPED
001-0-72 42 16 ACTIVE
001-1-00 NOT EQUIPPED
001-1-01 NOT EQUIPPED
001-1-02 NOT EQUIPPED
001-1-03 NOT EQUIPPED
001-1-10 NOT EQUIPPED
001-1-11 NOT EQUIPPED
001-1-12 NOT EQUIPPED
001-1-13 NOT EQUIPPED
001-1-20 NOT EQUIPPED
001-1-21 NOT EQUIPPED
001-1-22 NOT EQUIPPED
001-1-23 NOT EQUIPPED
001-1-30 NOT EQUIPPED
001-1-31 NOT EQUIPPED
001-1-32 NOT EQUIPPED
001-1-33 NOT EQUIPPED
001-1-40 NOT EQUIPPED
001-1-41 NOT EQUIPPED
001-1-42 NOT EQUIPPED
001-1-43 NOT EQUIPPED
****************************************************

Why Mag 1 is still reported? How can I definetly delete it?

Thanks
Mirko

 

[dstrang1]

Don't block the LIM before you send SFCEI.

You could also dump the system as it is on the printout, disconnect the DSU & power from MAG1 and poke the LPU for a reload. You should see 3100 on the display as it's coming back up.

Good luck,

Dave Strang

 

[fcpli]

Try this:

To ensure the actyal data:
sacop:unit=dcp,lim=1,sector=rel,addr=80&90;

To remove the magazine (mag1 in this case)
sacos:unit=dcp,lim=1,sector=rel,addr=96,data=00&f8&00&ff;
sacos:unit=dcp,lim=1,sector=rel,addr=90,data=00;

cnlip:lim=1,dev=yes;

Before you are removing the magazine, ensure that there are no cards etc. initiated (cnlip:lim=1,dev=yes again).