RAD 1

[JZJerry]

i have compact ics and i need to instoll Rad ,please help

 

[DueE]

CICS software has a IRAD, (Internal RAD), built in. If it is not enabled, you can order keycodes to activate it, or you can connect an external RAD by connecting to a station port and program it with the corresponding SYS ID # and password that you use with NRU or Norstar Manager.
DueE

 

[norstargirl]

If your installing a Rad onto a CICS what I do is Connect it onto a station port, I would put it on one of the last station ports so if you can CICS 0x16 put it on if you dont have vm I would put it on port 116 it connects just like a phone. I hope this helps.
Norstargirl M.Parnell
(norstargirl)

 

[jerryreeve]

After you have the above connections made you will have to put in an initial password in order to use the RAD remotely. First wait at least one minute, then from any 73XX phone press Feature 9**, the display shows Password EXIT CHNG NEXT Press the CHNG key and then enter the new password 8-10 digits) then press OK. Now you must re-enter the password, This prevents Fat Finger Troubles.

JerryReeve
Communications Systems Int'l
Jerry@com-sys.com

 

[JZJerry]

I still can't get RAD to work after i press F ** system say that this is not acctive feature; please help

 

[njphones]

Feature 9 * *
I hoe you did not forget the "9"
Is this a Rad or FastRad?
I do not know if some of the older Rad's are compatable with the CICS. I would think not.
You have to wait two to three minutes before entering feature 9 * * ( the manuel says one minute, but I give it three)
Hope this helps

 

[JZJerry]

I press Feature 9** and sysetm say that this is inactive feature and when i wait system hung up call

 

[DueE]

JZJerry, what is the system version of your CICS software? Are you using an external RAD or the internal RAD?
DueE

 

[mmazza]

What type of Rad are you using . FastRad or just a Rad?
what port do you have it cross connected to?
Make sure it is a station port and also make sure the power is on the rad.
Is the rad new or refurbished. I have a couple Refurbs bad out of the box.
Have you tried to Debug it.
Procedure for debug.

use a M7310
change date to April 15, 1999
F9**
hit left display key 5 times
hit center display key 6 times
hit right display key 8 times
press HOLD
press digit 2
press digit 1
press release/RAD now at
reset date
If you find a tip helpful Please take a moment to mark it as such.


Mario Mazza
Telecommunications Specialist

 

[JZJerry]

I have RAD not IRAD and i buy this item on ebay, system version SP:30JsH03NAT and this is a compact ICS, software 7,3 NT7B64AA, i tray all and i still have a problem.

 

[mmazza]

Sorry to say but I think someone got you on this one .
If I had to guess I would say it is a defective Rad.
Does it even answer if you do a OPeratod assit in?
If you find a tip helpful Please take a moment to mark it as such.


Mario Mazza
Telecommunications Specialist

 

[jerryreeve]

When you hook up the rad to the KSU does the red indicator flash? wait about 5 mins and then try the access via Feature 9 * *. JerryReeve
Communications Systems Int'l
com-sys.com

 

[vegasnortel]

I got bit for a couple bad RAD's on e-bay myself. Sometimes a "great deal" isn't so great after all! I would buy IRAD code from vendor or install Brand new FASTRad if it were me. Enabler code should be around 100-150 bucks and FastRAD about 175-250 depending on source.

This is not a solicitation! I do not sell FastRads or Codes! Just trying to help a Telcom Brother!

Rich

 

[JZJerry]

Thanks to all.
Regards Jerry

 

[jerryreeve]

Jerry
since you sound like you are giving up on the rad why don't you try this since it couldn't hurt you from where you are now. Open up the RAD and short out the battery (wafer battery) for 60 sec's. This will dump any password or other programming that the rad may have and it should be lookin like an unused device. JerryReeve
Communications Systems Int'l
com-sys.com

 

[JZJerry]

I change to IRAD ,i change password using 7310 and i call access number press F817 and i RAD pick up and i have massage on the computer that my password is wrong,

 

[jerryreeve]

Look at programming under passwords, the IRAD password is listed there. it defaults to be your system serial number. You will have to use the show button to look at it and be careful to read it correctly. the system SN is also visible under sosftware keys in programming. JerryReeve
Communications Systems Int'l
com-sys.com

 

[JZJerry]

I have Irad and i connected to the system ,when i dial in i press F817 and i see Irad but i don't have system id and i tray to find under passwords but is not there, i went to the system and under password in find only password for cor, and user i don,t have for instoller.Please HELP

Regards Jerry

 

[mmazza]

Just to clarify .
When you go to a 73xx connected to the system and type
F**266344 + password
scroll through till you get to password>show>scroll through till you get to IRAD>change.
you can't change your password.
I know if you are going in under the Admin password and not the installer you can't access the IRAD password.

If you find a tip helpful Please take a moment to mark it as such.


Mario Mazza
Telecommunications Specialist

 

[JZJerry]

i don't have instoller password and i try to change this password using IRAD,and the system is compact ICS