"new" 9730 - Many stored FSCs, what are they? 2

[PFarkas]

Clearly any 9730 isn't going to be "new"... But this unit passes the POST, makes no "unhappy belt" noises, and seems to be in decent shape (especially now that I removed most of a tape from the internal spool of DRV-1 and repositioned its leader).

However, many FSCs are stored - in fact there are 20.

I'd LOVE to be able to decode these FSCs myself. I'm sure there's a document floating around somewhere that explains what they mean, but I've been unable to find such a resource. In reading other posts, I've seen references to a "microcode disk" - I don't have one of these available to me, but if this is the StorageTek Rosetta Stone, I'd be delighted to get one.


I'm NOT expecting a detailed explaination for each FSC, but if there are any "Hey! That one's gonna be expensive!", I'd appreciate the heads up.

Anyway, I'll be testing this unit soon, prior to putting it into production and I'd like to know a little about its history.


Here are the codes that were stored in the sequence they were stored.
3304 None 781
3104 None 110
309D Reach 2
309D None 760
3106 None 74
309D Theta 1
3103 None 1
309D Z 1
309D Z 1
30B0 Reach
3216 Drv-2 9
3214 Drv-2 9
3216 Drv-0 11
3214 Drv-0 9
332A None 153
3216 Drv-1 1
3215 Drv-1 1
3205 Drv-2 9
3205 Drv-0 21
3288 None 1

From looking at the codes, the 32xx codes seem to have to do with the drives, and the 309D codes seel to have to do with the robot arm. No idea what the 31xx or the 33xx codes mean, nor do I have any idea about the third element in each code.

 

[OHWS]

I'm definitely not an expert in the hardware aspect, but I have seen the Theta and Reach errors on an L700e. From what I understand it could be a couple of different situations with those errors but the Theta and Reach error generally are common to see together and they usually point to the same issue. There could be an issue with the actual robot hand or with one of the motors powering the hand or the arm. I have no idea of what the NONE or the DRV errors point to. Please keep in mind that my situation could be unique to the L700e. Someone with more hardware experience could maybe give you a little more insight.

 

[comtec17]

What version of firmware is the library using?

These are the FSC Codes from Firmware Version 1.7.00

&&3001
ERR_FAULTY_DISPOSITION,
A non-specific error occurred - no other information is available.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 100
&&3002
ERR_UNEXPECTED_SYS_ERROR_RET,
An unexpected system return code was received by a task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 100
&&3003
ERR_NONE,
No error was found.
&&3004
ERR_LEVEL_15_OUT_OF_BOUNDS_ADDRESS,
An out of bounds address interrupt was detected by the processor logic.
It is possible (but not expected) that software can issue an instruction
which will address out of bounds RAM or I/O space.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 99
&&3005
ERR_WATCHDOG_TIMER_EXPIRED,
The watchdog timer has expired and is in the process of shutting down
the servos.
This can be caused by either a hardware failure OR a malfunction of the
software that refreshes the watchdog timer.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 90
Logical Error S/W 10
&&3081
ERR_SRV_UNKNOWN_REQUEST_TYPE,
An unknown type of request was received by Servo
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3082
ERR_SRV_UNEXPECTED_SYS_ERROR_RET,
An unexpected system return code was received by Servo
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3083
ERR_SRV_BAD_CHK_MOVE_CALC,
An error was encountered in performing a quick initialization move
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3084
ERR_SRV_DEST_OUTSIDE_OPER_RANGE,
The requested destination is not within the allowable operating range
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3085
ERR_SRV_ILLEGAL_PROFILE_TYPE,
An undefined profile type was requested
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3086
ERR_SRV_OVERCURRENT,
An overcurrent fault was detected by the hardware
Refer to specific FRU callouts for mechanism indicated
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
CYC LCU 75
THETA MTR/ENC. ASSY LSM 15
Theta/Z Flex Cable LSM 10
---> If MECH = Z<---
CYC LCU 75
Theta/Z Flex Cable LSM 25
---> If MECH = HAND<---
CYC LCU 65
HAND ASSY LSM 25
Hand Flex Cable LSM LOC: LSM LSM 10
&&3087
ERR_SRV_EXCESSIVE_POSITION_ERROR,
An excessive position error was detected during motion
Refer to specific FRU callouts for mechanism indicated.
Check robotic cabling connections and condition.
Check for any robotic obstructions.
Check z flex cabling connections and condition.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
CYC LCU 65
THETA MTR/ENC. ASSY LSM 20
THETA/Z Flex Cable LSM 15
---> If MECH = Z<---
CYC LCU 65
Z MTR/ENC. ASSY LSM 20
THETA/Z Flex Cable LSM 15
---> If MECH = HAND<---
CYC LCU 65
HAND ASSY LSM 20
Hand Flex Cable LSM 15
&&3088
ERR_SRV_EXCESSIVE_TACH_PHASE_ERRORS,
An excessive amount of tachometer phase errors was detected
Refer to specific FRU callouts for mechanism indicated
Check robotic cabling connections and condition.
Check z flex cabling connections and condition.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 15
Theta/Z Flex Cable LSM 10
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 15
Theta/Z Flex Cable LSM 10
---> If MECH = HAND<---
HAND ASSY LSM 65
CYC LCU 15
Hand Flex Cable LOC: LSM LSM 10
&&3089
ERR_SRV_EXCESSIVE_TACH_NOISE_ERRORS,
An excessive amount of tachometer noise errors was detected
Refer to specific FRU callouts for mechanism indicated
Check robotic cabling connections and condition.
Check z flex cabling connections and condition.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LOC: LSM 75
CYC LOC: LCU 25
---> If MECH = Z<---
Z MTR/ENC. ASSY LOC: LSM 75
CYC LOC: LCU 25
---> If MECH = HAND<---
HAND ASSY LOC: LSM 65
CYC LOC: LCU 25
Z flex cable assy LOC: LSM 10
&&308a
ERR_SRV_CANT_START__NOT_IN_STOPLOCK,
The requested motion cannot start because the mechanism is not stoplocked
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&308b
ERR_SRV_WATCH_DOG_TIMER_EXPIRED,
The watchdog timer has expired and has shutdown the servos (polled).
This can be caused by either a hardware failure OR a malfunction of the
software that refreshes the watchdog timer.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 80
Logical Error S/W 20
&&308c
ERR_SRV_ISR_REENTERED,
The servo interrupt service routine was re-entered before exiting
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&308d
ERR_SRV_SATURATION_CURRENT_REQUESTED_TOO_LONG,
The max or min current was requested an excessive amount of times
Refer to specific FRU callouts for mechanism indicated.
Check for obstructions in mechanisms. If failed on Cap operation
then check that the cap unlock button is not bound.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 20
Theta Flex Cable LSM 5
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 20
Z Flex Cable LSM 5
---> If MECH = HAND<---
HAND ASSY LSM 70
CYC LCU 25
Hand Flex Cable LSM 5
&&308e
ERR_SRV_MECH_DROPPED_OUT_OF_STOPLOCK,
The mechanism has fallen outside the allowable stoplock range
Refer to specific FRU callouts for mechanism indicated.
If this error is encountered at the end of a <put> operation, also
check for a loose or mispositioned target on the device used in the
previous <get> operation.
If this error occurred on a move then check belt tightness of
mechanisms.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = HAND<---
HAND ASSY LSM 65
CYC LCU 25
Hand Flex Cable LSM 10
&&308f
ERR_SRV_MECH_FAILED_TO_SETTLE_INTO_STOPLOCK,
The mechanism was unable to settle into the desired stoplock window
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = HAND<---
HAND ASSY LSM 65
CYC LCU 25
Hand Flex Cable LSM 10
&&3090
ERR_SRV_OPERATING_RANGE_OUT_OF_SPEC,
The range of motion on initialization is not within specification.
Check for obstructions in path of specified mechanism.
Check belt tensions!
If above are OK, then proceed with FRU replacements for specified mech.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 25
---> If MECH = HAND<---
HAND ASSY LSM 75
CYC LCU 25
&&3091
ERR_SRV_BAD_MECH_ID_IN_ISR,
The servo interrupt received a bad mechanism identifier
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3092
ERR_SRV_ILLEGAL_REQUEST_OPTION,
An illegal request option for Servo was requested
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3093
ERR_SRV_FAILED_TO_ENCOUNTER_CARTRIDGE,
The hand failed to encounter a cartridge
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 75
Hand flex cable LSM 15
CYC LCU 10
&&3094
ERR_SRV_FAILED_TO_DISENGAGE_CARTRIDGE,
The hand failed to dis-enagage a cartridge
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 75
Hand flex cable LSM 15
CYC LCU 10
&&3095
ERR_SRV_FAILED_TO_SEAT_CARTRIDGE,
The hand failed to seat a cartridge
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 75
Hand flex cable LSM 15
CYC LCU 10
&&3096
ERR_SRV_FAILED_TO_UNSEAT_CARTRIDGE,
The hand failed to unseat a cartridge
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 75
hand flex cable LSM 15
CYC LCU 10
&&3097
ERR_SRV_REQUEST_ALREADY_ACTIVE_AGAINST_MECHANISM,
Request rejected - motion is already active against mechanism
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3098
ERR_SRV_CANT_MOVE_ARM__HAND_IS_ACTIVE,
Arm Request rejected - hand is currently active
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3099
ERR_SRV_CANT_MOVE_HAND__ARM_IS_ACTIVE,
Hand Request rejected - arm is currently active
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&309a
ERR_SRV_UNEXPECTED_RESP_AT_DISPATCHER,
The Servo Dispatcher received an expected response
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&309b
ERR_SRV_CANT_GET_WITH_HAND_FULL,
Get Request rejected - hand is already full
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&309c
ERR_SRV_CANT_PUT_WITH_HAND_EMPTY,
Put Request rejected - hand is empty
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&309d
ERR_SRV_ACCESS_DOOR_IS_OPEN,
Access door is open.
All robot activity in the library has been aborted.
First confirm the doors are closed and aligned correctly before
proceeding with FRU replacements. Check the interlock cable condition.
FRU: LOCATION: CONFIDENCE %:
SW, DOOR LSM 80
CYC LCU 20
&&309e
ERR_SRV_MOVE_ABORTED,
The request ended in failure due to an abort request
Abort requests are issued to all mechanisms on Door Openings,
Power Supply Failures, Hardware Faults, and Power Off Requests.
Abort requests are issued to a selective mechanism due to a specific
failure with that mechanism. Refer to prior events leading up to this
failure.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&309f
ERR_SRV_HAND_NOT_SAFE__HAND_IS_INOPERATIVE,
Hand is not safe - the hand is not operative.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 65
CYC LCU 25
Hand Flex Cable LSM LSM 10
&&30a0
ERR_SRV_HAND_NOT_SAFE__REACH_NOT_RETRACTED,
Hand is not safe - reach is not retracted.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 65
CYC LCU 25
Hand Flex Cable LSM LSM 10
&&30a1
ERR_SRV_HAND_NOT_SAFE__CARTRIDGE_IS_UNSEATED_IN_GRIP,
Hand is not safe - a cartridge is unseated in the grip.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 65
CYC LCU 25
Hand Flex Cable LSM LSM 10
&&30a2
ERR_SRV_MECHANISM_NOT_INITIALIZED,
Mechanism must be first initialized.
Refer to prior events leading up to this failure.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&30a3
ERR_SRV_MECHANISM_PERMANENTLY_SHUTDOWN,
The mechanism has been permanently shutdown - IPL or open/close door
Refer to prior events leading up to this failure.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&30a4
ERR_SRV_MECHANISM_NOT_OPERATIONAL,
The mechanism is not operational. Refer to prior events leading up to
this failure.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&30a5
ERR_SRV_USER_REQ_GT_100MIL_THETA_MOVE_FOR_SCAN,
A Z scan was requested with a theta motion greater than 100 mils. Check
to make sure all arrays are snapped in properly.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&30a6
ERR_CAP_HDW_FAILED_TO_DETECT_UNLOCK,
CAP sensor failed to detect the unlocked position
Check to see that the hand was able to depress the plunger, then take
appropriate action.
FRU: LOCATION: CONFIDENCE %:
CAP Switch LSM 85
CAP Latch Assm LSM 10
CYC LCU 5
&&30a7
ERR_SRV_CAP_OPEN_INT_MISSED,
Failed to receive the CAP open interrupt during the unlock operation.
FRU: LOCATION: CONFIDENCE %:
CAP Switch LSM 85
CAP Latch Body Assm LSM 10
CYC LCU 5
&&30a8
ERR_SRV_CANT_UNLOCK_CAP_WITH_HAND_FULL,
Cap Unlock Request rejected - hand is full
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&30a9
ERR_SRV_CANT_CLEAR_AMP_ENABLE,
Could not clear a bit in the amp enable register during fault
processing. The fault cannot be cleared until the amp enable register
is cleared.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 90
Logical Error S/W 10
&&30aa
ERR_SRV_SATURATION_CURRENT_READ_TOO_LONG,
The max or min current was read an excessive amount of times by the
analog to digital converter. Check for obstructions, then proceed
with FRU replacements. Refer to specific FRU callouts for
the mechanism indicated.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
CYC LOC: LCU 70
THETA MTR/ENC. ASSY LOC: LSM 30
---> If MECH = Z<---
CYC LOC: LCU 70
Z MTR/ENC. ASSY LOC: LSM 30
---> If MECH = HAND<---
CYC LOC: LCU 70
HAND ASSY LOC: LSM 20
Z flex cable assy LOC: LSM 10
&&30ab
ERR_SRV_MINIMUM_INIT_MOVE_NOT_DETECTED,
During initialization for the mechanism indicated, the software did
not detect a change in the tach counter near the beginning of the
move and has assumed the tach is not functioning.
Check for any obstructions and for cables properly connected, then
proceed with FRU replacements.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
CYC LCU 50
THETA MTR/ENC. ASSY LSM 30
Theta Flex Cable LSM 20
---> If MECH = Z<---
CYC LCU 50
Z MTR/ENC. ASSY LSM 20
Z Flex Cable LSM 20
---> If MECH = HAND<---
CYC LCU 60
HAND ASSY LSM 30
Hand Flex Cable LSM 5
&&30ac
ERR_SRV_CANT_OPERATE_DLT_WITH_HAND_FULL,
DLT Drive Handle Operation Request rejected - hand is full
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&30ad
ERR_SRV_CANT_PUSH_WITH_HAND_FULL,
Push Request rejected - hand is already full
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&30ae
ERR_SRV_CANT_GET_WITH_LATCH_DOWN,
Get request rejected, cannot get with cartridge latch in the down
position.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&30af
ERR_SRV_FAILED_TO_LATCH_CART_ON_GET,
Hand could not latch the cartridge during a get operation.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 65
Logical Error S/W 20
CYC LCU 15
&&30b0
ERR_SRV_AMP_ENABLE_FAIL,
The mechanism amplifier could not be enabled. Register bit could not
be set to a logical high.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
CYC LCU 60
Power Supply ASSY LOC: LCU 25
THETA MTR/ENC. ASSY LSM 15
---> If MECH = Z<---
CYC LCU 60
Power Supply ASSY LOC: LCU 25
Z MTR/ENC. ASSY LSM 15
---> If MECH = Reach<---
CYC LCU 60
Power Supply ASSY LOC: LCU 25
HAND ASSY LSM 15
&&30b1
ERR_SRV_FAILED_STALL,
The mechanism stall point was outside of allowable tolerances. Check
for obstructions.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
THETA MTR/ENC. ASSY LSM 75
CYC LCU 15
Power Supply ASSY LOC: LCU 10
---> If MECH = Z<---
Z MTR/ENC. ASSY LSM 75
CYC LCU 15
Power Supply ASSY LOC: LCU 10
---> If MECH = Reach<---
HAND ASSY LSM 75
CYC LCU 15
Power Supply ASSY LOC: LCU 10
&&30b2
ERR_SRV_FAILED_STALL__OBSTRUCTED,
The hand stall point was too close to the hand to be sure of a
clear operating path for the robot. Check for obstructions in the
cell and for a good hand operating range.
FRU: LOCATION: CONFIDENCE %:
---> If MECH = Theta<---
Logical Error S/W 100
---> If MECH = Z<---
Logical Error S/W 100
---> If MECH = Reach<---
HAND ASSY LSM 75
CYC LCU 15
Power Supply ASSY LOC: LCU LCU CONF_%: 10 10
&&30b3
ERR_SRV_DEST_OUTSIDE_OPER_RANGE_ADJUSTED,
The requested destination is not within the allowable operating range.
The destination was adjusted to the minimum or maximum destination
allowable and the move will be attempted anyway. This error code is
strictly informational.
FRU: LOCATION: CONFIDENCE %:
NONE NONE NONE
&&30b4
ERR_SRV_NOT_RESPONSE_DISCARDED,
A srv_response message was expected, but another type of message was
received. The message received was ignored and deleted.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&30b5
ERR_SRV_CANT_FIND_REACH_DEPTH,
Reach and touch rejected - hand is full
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 60
HAND ASSY LSM 25
CYC LCU 15
&&3101
ERR_ITL_NOT_INIT_CMD,
During initialize a non-initialization command was received.
FRU: LOCATION: CONFIDENCE %:
Logical Error LSM 99
&&3102
ERR_ITL_NOT_FIRST_PHASE,
The first initialize command received was not the first phase.
May be Caused by Repeated Door open/closings.
FRU: LOCATION: CONFIDENCE %:
Logical Error LSM 99
&&3103
ERR_ITL_OUT_OF_SEQUENCE,
An initialize command was received that was out of sequence.
FRU: LOCATION: CONFIDENCE %:
Logical Error LSM 99
&&3104
ERR_ITL_FAILED_REACH_RETRACT,
The hand failed retracting to a safe position.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 85
Z flex cable assy LSM 10
CYC LCu 5
&&3105
ERR_ITL_FAILED_ARM_INIT_START,
The Arm (Theta and/or Z) initialization failed to start.
Check for any robotic obstructions.
FRU: LOCATION: CONFIDENCE %:
THETA MOTOR LSM 40
Z MOTOR LSM 40
CYC LCU 15
Flex Cable LSM 5
&&3106
ERR_ITL_FAILED_ARM_INIT,
The Arm (Theta and/or Z) failed initialization.
FRU: LOCATION: CONFIDENCE %:
THETA MOTOR LSM 40
Z MOTOR LSM 40
CYC LCU 15
Flex Cable LSM 5
&&3107
ERR_ITL_FAILED_NONESSENTIAL_MECH_INIT,
Unused error.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 100
&&3108
ERR_ITL_HAND_INIT_FAILED,
The hand failed initialization. Also check the calibration area for
obstructions.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 70
CYC LCU 25
&&3109
ERR_ITL_HAND_CAMERA_CALIB_FAIL,
The Hand to Camera calibration failed.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&310a
ERR_ITL_HAND_SENSOR_FAIL,
A move to the hand test area failed.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&310b
ERR_ITL_TEST_LSC_TARGET_ILLUM_FAIL,
The test for the Line Scan Camera (LSC) target illumination failed. Make
sure the CAP is closed.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&310c
ERR_ITL_TEST_LSC_BARCODE_ILLUM_FAIL,
The test for the Line Scan Camera (LSC) barcode illumination failed.
Make Sure Cap Door is closed!
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&310d
ERR_ITL_TEST_LSC_VISION_FAIL,
The test for the Line Scan Camera (LSC) vision failed.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&310e
ERR_ITL_AUDIT_FAIL,
An audit of a cell or cells failed. This could be caused by multiple
conditions. See prior errors for more better FRU isolation.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 5
Logical Error S/W 5
&&310f
ERR_ITL_FAILED_TO_GO_OFFLINE,
The LSM failed to go offline.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 100
&&3110
ERR_ITL_AUDIT_CONFIG,
A cell target was not found during initial audit.
During the initialization full panel audit a cell target
was not found. There may be a configuration error.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 70
CYC LCU 25
Logical Error S/W 5
&&3111
ERR_ITL_DRIVE_STATUS_FAIL,
A drive status failed. This could be caused by multiple
conditions. See prior errors for better FRU isolation.
FRU: LOCATION: CONFIDENCE %:
DRIVE LCU 75
CYC LCU 10
TTI Cable LCU 10
Logical Error S/W 5
&&3181
ERR_MOT_INVALID_ADDRESS,
The LSM received an invalid address.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3182
ERR_MOT_INVALID_ADDRESS_TYPE,
The LSM received an invalid address type.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3183
ERR_MOT_BAD_HAND_PARAMETER,
The LSM received an invalid hand specifier.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3184
ERR_MOT_VALIDATION_PARAMETER,
The LSM received an invalid VOLSER verification parameter.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3185
ERR_MOT_BAD_VOLSER,
The LSM received an invalid VOLSER.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3186
ERR_MOT_BAD_MEDIA_TYPE,
The LSM received an invalid media specifier.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3187
ERR_MOT_CAP_NOT_LOCKED,
The LSM received a motion request against an unlocked CAP.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3201
ERR_CMO_FAILED_REACH_RETRACT,
Reach failed to successfully retract to a safe position.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 85
Hand flex cable LSM 10
CYC LCU 5
&&3202
ERR_CMO_FAILED_ARM_INIT,
The Arm (Theta and/or Z) failed initialization.
FRU: LOCATION: CONFIDENCE %:
THETA MOTOR LSM 40
Z MOTOR LSM 40
CYC LCU 15
FLEX CABLE LSM 5
&&3203
ERR_CMO_FAILED_HAND_INIT,
Hand failed initialization.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 85
Hand flex cable LSM 10
CYC LCU 5
&&3204
ERR_CMO_FAILED_RETRY_PREPARATION,
During preparation for retry, a failure was encountered.
Refer to prior failures for FRU isolation.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&3205
ERR_CMO_ELEVATOR_NOT_UP,
The cartridge drive handle/elevator is not up.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
CYC LCU 5
&&3206
ERR_CMO_TRANSPORT_EMPTY,
The cartridge drive is empty.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
CYC LCU 5
&&3207
ERR_CMO_TRANSPORT_FULL,
The cartridge drive is full.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
CYC LCU 5
&&3208
ERR_CMO_HAND_EMPTY_ON_PUT,
Cannot Put the cartridge, the hand is empty.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&3209
ERR_CMO_CELL_FULL_ON_PUT,
Cannot Put the cartridge, the cell is full.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 90
HAND ASSY LSM 10
&&320a
ERR_CMO_HAND_FULL_ON_GET,
Cannot Get the cartridge, the hand is already full.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 5
FLEX CABLE LSM 5
&&320b
ERR_CMO_CELL_EMPTY_ON_GET,
Cannot Get the cartridge, the cell is empty.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 95
CYC LCU 5
&&320c
ERR_CMO_LABEL_UNEXPECTEDLY_READABLE,
The label was unexpectedly readable.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 90
HAND ASSY LSM 10
&&320d
ERR_CMO_LABEL_READABLE_ON_GET,
The label was found readable on a Get operation.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 90
CYC LCU 10
&&320e
ERR_CMO_LABEL_MISMATCH_ON_GET,
The label requested mismatches with that found in the LSM database.
Non fatal error caused by host system requesting wrong volser.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&320f
ERR_CMO_MEDIA_MISMATCH,
A mismatch in media type was found.
Non fatal error caused by host system requesting wrong media type.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&3210
ERR_CMO_CCD_HAND_READ_FAILURE,
A request for label information of the cartridge previously in the hand
failed.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 90
Logical Error S/W 10
&&3211
ERR_CMO_CCD_CELL_READ_FAILURE,
A request for label information of the cartridge previously in a cell
failed unexpectdely.
FRU: LOCATION: CONFIDENCE %:
CYC LCU 90
Logical Error S/W 10
&&3212
ERR_CMO_UNKNOWN_MEDIA_ON_GET,
Cannot execute a get instruction on a cartridge whose media type is
unknown. For Multimedia configurations, The cartridge must be
labeled for the library to work with it.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&3213
ERR_CMO_UNKNOWN_MEDIA_ON_PUT,
Cannot execute a put to a drive when the cartridge media type is
unknown. The cartridge must be labeled for the library to work with it.
FRU: LOCATION: CONFIDENCE %:
NONE NONE 100
&&3214
ERR_CMO_FAILED_INFLUX_RECOVERY,
Cannot clear the influx condition on a DLT drive. Attempt to
reinitialize the drive with the load handle down before proceding
with FRU replacements.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 90
HAND ASSY LSM 5
CYC LCU 5
&&3215
ERR_CMO_CART_PRESENT_AFTER_INFLUX_RECOVERY,
The drive is reporting a cartridge present after an influx recovery
operation was performed. Check for and remove any cartridge in the
drive, or try reinitializing the drive with the handle down before
proceding with FRU replacements.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
CYC LCU 5
&&3216
ERR_CMO_DRIVE_STATE_NOT_VERIFIED,
The drive state cannot be verified before attempting a load or unload
operation. Either drive communication failed or the drive could not be
initialized.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
PRC LCU 5
&&3217
ERR_CMO_DRV_INFLUX__HANDLE_DOWN,
The drive is reporting an influx condition with the handle down.
Influx recovery cannot be performed on a drive with the handle down.
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
PRC LCU 5
&&3218
ERR_CMO_FAILED_GET_DLT_DRV,
Failed get from DLT drive
FRU: LOCATION: CONFIDENCE %:
DRIVE LSM 95
PRC LCU 5
&&3281
ERR_VAU_BAD_PANEL_ID,
Bad panel ID passed from upper level routine to virtual
audit routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3282
ERR_VAU_BAD_CAP_ID,
Bad CAP ID passed from upper level routine to virtual
audit routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3283
ERR_VAU_BAD_DRIVE_PANEL_ID,
Bad Drive ID passed from upper level routine to virtual
audit routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3284
ERR_VAU_UNKNOWN_MECH_TYPE,
Unknown mechanism type passed from upper level routine to virtual
audit routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3285
ERR_VAU_GEN_TARGETS_BAD_ADDR,
Bad target address generated in virtual
audit routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3286
ERR_VAU_ASSOC_CELLS_ADDRESS,
Bad associated cell address generated in virtual audit.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3287
ERR_VAU_BAD_CALIB_ADDRESS,
Bad calibration cell address generated in virtual audit.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&3288
ERR_VAU_PHYSICAL_AUDIT_FAIL,
A physical audit was issued and failed. Log events regarding the
nature of the failure, either servo or vision, should have reported
prior to this event log. Use these fru replacements prior to the
ones reported here.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 50
CYC LCU 45
HAND FLEX CABLE LSM 05
&&3289
ERR_VAU_TARGET_NOT_CALIB,
A request for auditing a set of cells was requested prior to
the target being calibrated.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
&&328a
ERR_VAU_TARG_CALIB_CHECK_FAIL,
A audit of a target was performed and the returned location was outside
the accepable window. If there are events regarding the nature of the
failure, prior to this one there FRU replacement should be followed.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 50
CYC LCU 50
&&328b
ERR_VAU_TARG_MAGAZINE_FAIL,
A audit of a target was performed and the target did not exist.
The removable magazine must be present for the library to function.
FRU: LOCATION: CONFIDENCE %:
MAGAZINE LSM 98
HAND ASSY LSM 1
CYC LCU 1
&&3301
ERR_AUD_INVALID_PROC_LINE_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error LOC: S/W CONF_%: 98 98
HAND ASSY LOC: LSM CONF_%: 01 01
CYC LOC: LSM CONF_%: 01 01
&&3302
ERR_AUD_INVALID_UNSCRAMBLE_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error LOC: S/W CONF_%: 98 98
HAND ASSY LOC: LSM CONF_%: 01 01
CYC LOC: LSM CONF_%: 01 01
&&3303
ERR_AUD_INVALID_CLASS,
Software error occurred in trying to decode picture of label
and specifically the class of the label.
FRU: LOCATION: CONFIDENCE %:
Logical Error LOC: S/W CONF_%: 98 98
HAND ASSY LOC: LSM CONF_%: 01 01
CYC LOC: LSM CONF_%: 01 01
&&3304
ERR_AUD_UNREADABLE_LABEL,
When scanning down past a cartridge the label could not be read.
Three re-trys are done on each unreadable label so unless all
retries are logged as failures no action should be taken. If
numerous locations are failing it could possibly be that the
camera is not working and the hand assembly should be switched.
If the customer uses unlabeled cartridges in their library, this
error will appear frequently.
NOTE: If the unit is equipped with the Removable Cartridge Magazine
feature, ensure that the Magazine is present and properly
installed.
FRU: LOCATION: CONFIDENCE %:
Non-Fatal Logical Err S/W CONF_%: 99 99
HAND ASSY LSM CONF_%: 01 01
CYC LSM CONF_%: 01 01
&&3305
ERR_AUD_INVALID_BUILD_BARCODE_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error LOC: S/W CONF_%: 98 98
HAND ASSY LOC: LSM CONF_%: 01 01
CYC LOC: LSM CONF_%: 01 01
&&3306
ERR_AUD_BUILD_COMP_ERR,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error LOC: S/W CONF_%: 98 98
HAND ASSY LOC: LSM CONF_%: 01 01
CYC LOC: LSM CONF_%: 01 01
&&3307
ERR_AUD_INVALID_BUILD_COMP_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM CONF_%: 01 01
CYC LSM CONF_%: 01 01
&&3308
ERR_AUD_RUNLENGTH_DECODE_ERR,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM CONF_%: 01 01
CYC LSM CONF_%: 01 01
&&3309
ERR_AUD_INVALID_RUNLENGTH_DECODE_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM CONF_%: 01
CYC LSM CO 01
&&330a
ERR_AUD_THRESHOLD_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM 01
CYC LSM 01
&&330b
ERR_AUD_FIND_CHAR_STATUS,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98
HAND ASSY LSM 01
CYC LSM 01
&&330c
ERR_AUD_INVALID_SERVO_RESPONSE,
Software error occurred in trying to position servo systems
(theta and z) for scanning cartridge or target locations.
Servo errors that proceed this error should be followed for
corrective action.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W (LSM Log Requested) 99
&&330d
ERR_AUD_INVALID_REQUEST_PACKET,
Software error occurred in trying to decode picture of label
or target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM CONF_% 01
CYC LSM 01
&&330e
ERR_AUD_INVALID_MULTISCAN_STATUS,
Software error occurred in trying to detect cartridge in cell.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF 98
HAND ASSY LSM 01
CYC LSM 01
&&330f
ERR_AUD_INVALID_TARGET,
Software error occurred in trying to decode picture of target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98
HAND ASSY LSM 01
CYC LSM 01
&&3310
ERR_AUD_INVALID_FIND_BARS_STATUS,
Software error occurred in calibrating vision system.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_ 98
HAND ASSY LSM 01
CYC LSM 01
&&3311
ERR_AUD_TARGET_UNREADABLE,
When scanning down past a calibration target the target was
unable to be de-coded. Three re-trys are done on each unreadable
target so unless all retries are logged as failures no action
should be taken. If numerous targets are failing it is likely
that the hand assembly needs to be replaced.
POSSIBLE CONFIGURATION PROBLEM - If the library is configured for
less then 4 drives the optional two cell pack must be installed and
locked down in the fourth drive slot.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM CONF_ 70
CYC LSM CONF_ 20
Hand Flex Cable LSM CONF_%: 10 10
&&3312
ERR_AUD_MASTER_TARGET_UNREADABLE,
While scanning the master target, it was unable to be decoded.
This occurs most often before the library is calibrated, when
different camera values need to be tried before it is possible
to read the target. Three trys are done on the target so unless
all retries are logged as failures no action should be taken.
FRU: LOCATION: CONFIDENCE %:
CYI LSM CONF_ 50
CYC LSM CONF_ 30
Hand Flex Cable LSM CONF_ 10
HAND ASSY LSM CONF_ 10
&&3313
ERR_AUD_STATIC_TARGET_UNREADABLE,
When doing a stationary calibration of a target, a target could
not be found.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM CONF_ 70
CYC LSM CONF_ 20
Hand Flex Cable LSM CONF_%: 10 10
&&3314
ERR_AUD_INVALID_ENTITY_COUNT,
Software error occurred in packet being sent to audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC L LSM CONF_%: 01
&&3315
ERR_AUD_INVALID_STATIC_PIC_STATUS,
Software error occurred in static picture taken.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 98 98
HAND ASSY LSM CONF_ 01
CYC LSM CONF_ 01
&&3316
ERR_AUD_INVALID_USER_REQUEST,
Software error occurred in packet being sent to audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU CONF_%: 01
&&3317
ERR_AUD_USER_RESPONSE_TIMEOUT,
Software error occurred in packet being sent to audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU CONF_%: 01 01
&&3318
ERR_AUD_INVALID_RECEIVE_STATUS,
Software error occurred in packet being received from audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU CONF_%: 01 01
&&3319
ERR_AUD_LEFT_OVER_PACKET,
Non-fatal logging messgae that requires no field action.
FRU: LOCATION: CONFIDENCE %:
Non-Fatal Logical Err S/W CONF_%: 99 99
&&331a
ERR_AUD_INVALID_SCAN_RESPONSE,
Invalid message received from scan process.
FRU: LOCATION: CONFIDENCE %:
Non-Fatal Logical Err S/W CONF_%: 99 99
CYC LMU CONF_%: 01
&&331b
ERR_AUD_SCAN_RESPONSE_TIMEOUT,
No message received from scan process.
FRU: LOCATION: CONFIDENCE %:
Fatal Logical Err L S/W CONF_%: 99 99
CYC LMU CONF_%: 01
&&331c
ERR_AUD_INVALID_TARGET_STATUS,
Received invalid response when taking a stationary picture of
a target.
FRU: LOCATION: CONFIDENCE %:
Fatal Logical Err S/W CONF_%: 99 99
CYC LMU CONF_%: 01 01
&&331d
ERR_AUD_INVALID_PROCESS_IMAGE_RESPONSE,
Software received an invalid return from a image processing
routine.
FRU: LOCATION: CONFIDENCE %:
Fatal Logical Err L S/W CONF_%: 99 99
CYC L LMU CONF_%: 01
&&331e
ERR_AUD_INVALID_FLAG,
Software error occurred in packet being sent to audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU CONF_%: 01
&&331f
ERR_AUD_INVALID_ENTITY,
Software error occurred in packet being sent to audit task.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU CO 01
&&3320
ERR_AUD_INVALID_SCAN_LOC_RESPONSE,
Software error occurred in packet being received from scaning
a location.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU 01
&&3321
ERR_AUD_SCAN_OVERFLOW_IN_SCAN_LOCATION,
Non-fatal logging message that requires no field action.
FRU: LOCATION: CONFIDENCE %:
Non-Fatal Logical Err S/W CONF_%: 99 99
&&3322
ERR_AUD_INVALID_READ_STATUS,
Invalid Condtion Software Error.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU 01
&&3323
ERR_AUD_INVALID_FIND_CHECK_LINE_STATUS,
Software error occurred in packet being received from scanning
a location.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
CYC LMU 01
&&3324
ERR_AUD_INVALID_ILLUMINATE_CHECK,
Software error occurred in invalid response received from
illumination check routine.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
HAND ASSY LSM 01
&&3325
ERR_AUD_FOCUS_FACTOR_INVALID_STATUS,
Software error occurred in calculating focus factor for
camera.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
HAND ASSY LSM 01
&&3326
ERR_AUD_VISION_CHECK_UNREADABLE,
Software could not fine the vision check error of the playground
during initilization. Most likely camera is no longer working.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 80
CYC ASSY LCU Card Cage 20
&&3327
ERR_AUD_FIELD_OF_VIEW_INVALID_STATUS,
Software error occurred in calculating field of view of
camera.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
HAND ASSY LSM 01
&&3328
ERR_AUD_INVALID_FIND_4400_BAR_STATUS,
Software error occurred in trying to read a magazine target.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W CONF_%: 99 99
HAND ASSY LSM 01
&&3329
ERR_AUD_CALIBRATION_FAILURE,
Note: In the CAP open position the CAP mechanism blocks the calibration
label. If the CAP is opened close it and then open and close the door
to re-start the initialization.
The camera calibration routines couldn't find a valid operating point.
This may be because the calibration label is not installed, installed
improperly or the camera and/or related circurity is not working.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM CO 50
CYC LSM C 25
CALIBRATION LABEL LSM C 24
Logical error S/W C 01
&&332a
ERR_AUD_UNREADABLE_LABEL_FINAL,
Three retries were exausted trying in vain to read a cartridge label
or a calibration target.
POSSIBLE CONFIGURATION PROBLEM - If the library is configured for
less then 4 drives the optional two cell pack must be installed and
locked down in the fourth drive slot.
If the cartridge is not labeled, this is not a true error.
If the customer uses unlabeled cartridges in their library this error
will appear frequently.
If numerous locations are failing it could possibly be that the
proimity sensor or camera are not working and the hand assembly
should be switched.
FRU: LOCATION: CONFIDENCE %:
Non-Fatal Logical Err S/W CO 10
HAND ASSY LSM CO 45
Cartridge Label LSM CO 45
&&3381
ERR_CLB_TARGET_UNREADABLE,
Camera could not find expected target. If this error occurs during
its first initilization then the machine is probably not configured
properly. This can be rectified by noting the cartridge location
of the cells inside the library and using the config environemnt
to verify the proper configuration. It could also be caused by
the tape drives not being installed, latched or having a target.
FRU: LOCATION: CONFIDENCE %:
HAND ASSY LSM 80
CYC LCU 20
&&3382
ERR_CLB_LSC_FAILURE,
The upper level calibration received an invalid return value
from the low-level physical audit software.
FRU: LOCATION: CONFIDENCE %:
Logical Error S/W 99
CYC LC